Results 131 to 140 of about 35,929 (259)
Advanced Materials Technologies, EarlyView.A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala +5 more
wiley +1 more source
Analysis of Residual Stress at the Interface of Epoxy-Resin/Silicon-Wafer Composites During Thermal Aging. [PDF]
Polymers (Basel)Wu J +6 more
europepmc +1 more source
Reconnaissance Peptide Labeling Grain Boundary of Chemically Grown MoS2 Polycrystalline Monolayer
Advanced Materials Technologies, EarlyView.Self‐assembled peptides on substrates, through adsorption and aggregation, offer an alternative way to label grain boundaries in chemically grown single‐layer polycrystalline MoS2. During an early nucleation step, peptides preferentially bind to grain boundaries.
Linhao Sun, Jinhua Hu
wiley +1 more source
Piezoelectric Micromachined Ultrasonic Transducers with Micro-Hole Inter-Etch and Sealing Process on (111) Silicon Wafer. [PDF]
Micromachines (Basel)Wang Y, Wu S, Wang W, Wu T, Li X.
europepmc +1 more source
Advanced Materials Technologies, EarlyView.Flexible silicon carbide (SiC) microelectrode arrays enable high‐fidelity, multichannel cell extracellular recording and precise localized ablation. SiC has been extensively evaluated to persist long‐term in chronic physiological conditions while remaining robust, with excellent electrical and electrochemical stability.
Minh Anh Huynh +4 more
wiley +1 more source
Fabrication of Ordered Macropore Arrays in n-Type Silicon Wafer by Anodic Etching Using Double-Tank Electrochemical Cell. [PDF]
Micromachines (Basel)Zhang J, Zhang F, Ma M, Liu Z.
europepmc +1 more source
Fully Printed Electrocaloric Heat Pump
Advanced Materials Technologies, EarlyView.A system based on a flexible printed PEDOT:PSS/P(VDF‐TrFE‐CFE) electrocaloric membrane. The membrane periodically alternates between the cold and hot sides following its electrocaloric cycle and successfully generates a temperature difference. The entire fabrication process is industrially scalable, cost‐effective, and based on widely accessible ...
Adrian Agreda +7 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee +2 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.A direction‐aware piezo‐transmittance strain sensor is realized through the engineered alignment of carbon nanotubes. This anisotropic architecture instantaneously modulates optical transmittance, achieving ultra‐high sensitivity and exceptionally low hysteresis. By effectively eliminating signal crosstalk to precisely decouple multidirectional strains,
Byeongmin Kang +15 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.An in situ integrated TiO2/SiOx/Al2O3 synaptic phototransistor couples ultraviolet and electrical stimuli within a scalable, CMOS‐compatible oxide stack. Multimodal plasticity, spike‐timing‐dependent learning, and bee‐inspired associative conditioning are achieved through trap‐mediated temporal dynamics.
Youngbin Yoon +5 more
wiley +1 more source