Results 21 to 30 of about 2,384 (206)
Archives of Foundry Engineering, 2015 The work presents the results of the examinations of silumin 226 as well as a silumin produced on its basis containing a W and Mo addition introduced in the amount of 0.1; 0.2; 0.3 and 0.4% of both elements simultaneously.
Szymczak T. +3 more
doaj +1 more source
An Application for Infrared Camera in Analyzing of the Solidification Process of Al-Si Alloy
Archives of Foundry Engineering, 2015 The paper presents the results of the crystallization process of silumin by the TDA thermographic method and the results of the cast microstructure obtained in the sampler TDA-10, that was cooling down in ambient air.
Władysiak R., Kozuń A.
doaj +1 more source
Effect of the Hold Time and Temperature on Characteristic Quantities of TDA Curves [PDF]
, 2014 This paper presents the effect of the temperature and hold time in the holding furnace of 226 silumin on the characteristic quantities of TDA curves.
Gumienny, Grzegorz +2 more
core +2 more sources
MANUFACTURE AND USE OF SILUMIN WITH GLOBULAR SILICON
Литьë и металлургия, 2017 Methods of production of silumin with globular silicon are developed. The manufacturing of this new antifriction material are organized. The wear resistance and operational life of articles from silumin with globular silicon are on par with or surpass ...
E. I. Marukovich +2 more
doaj +1 more source
Influence of soaking time of modifier in melt on microstructure of Al-12%Si alloys [PDF]
, 2017 The influence of the soaking time of the silumin melt with a modifying nanopowder W on the microstructure and the impact toughness of the Al-12%Si silumin is studied in the paper. It was established that when introducing 0.1 mass.
Bashev, V. S. +2 more
core +1 more source
Idosr Journal of Science and Technology, 2023 This study utilizes response surface methodology (RSM) to estimate the engineering parameters of PFAP/silumin composites. The tensile strengths of the developed composites were evaluated using a Box-Behnken design (BBD), considering factors such as ...
O. O. Barah
semanticscholar +1 more source
STRUCTURAL-PHASE STATE OF SILUMIN OF HYPEREUTECTIC COMPOSITION IRRADIATED BY A PULSED ELECTRON BEAM
Физико-химические аспекты изучения кластеров, наноструктур и наноматериалов, 2020 Silumin (an alloy of aluminum with silicon) is a cheap industrial alloy with good corrosion resistance, high specific mechanical properties and good casting properties.
Yu.F. Ivanov +5 more
doaj +1 more source
Structure-phase states of silumin surface layer after electron beam and high cycle fatigue [PDF]
, 2015 Modification of eutectic silumin surface has been implemented by high-intensity pulsed electron beam. The irradiation mode has been revealed; it allows increasing silumin fatigue life in more than 3.5 times.
Alsaraeva, K. V. +3 more
core +1 more source
Archives of Foundry Engineering, 2015 The paper presents the results of hypoeutectic silumin 226 grade and silumin produced on its basis through the addition of V and Mo. Vanadium and molybdenum were added as the preliminary alloy AlV10 and AlMo8 in an amount providing the concentration of 0.
Szymczak T., Gumienny G., Pacyniak T.
doaj +1 more source
Research into morphology and phase structure in the surface of Al-Si alloy modified by yttrium oxide [PDF]
Bulletin of the Polish Academy of Sciences: Technical Sciences, 2019 Using methods of physical material studies (scanning electron microscopy and micro X-ray spectral analysis), a study was carried out with focus on alteration of structure and phase composition in surface layers of Al-Si alloy (silumin АК10М2N) treated in
D. Zagulyaev +4 more
doaj +1 more source