Results 151 to 160 of about 4,032,596 (264)

Virtual Nurse Discharge: Improving Patient and Nurse Experience

This case study reviews the virtual discharge nurse (VDN) process and its impact on patient experience and nursing workflow as an exemplar of an effective telehealth innovation at a community hospital 23-bed Short Stay Unit (SSU).
Wright, Fay, Oates, Carolyn, Davis, Stacey, Flihan, Dina, Odell, Christine   +4 more
core   +1 more source

Lab‐in‐a‐Tube System Integrating Hierarchically Wrinkled Electrodes and DNAzyme‐Functionalized Beads for Diagnosis of Clostridioides difficile Infection

Advanced Materials, EarlyView.
The point‐of‐care diagnosis of Clostridioides difficile infection remains challenging due to reliance on slow culture and amplification‐based methods. A lab‐in‐a‐tube electrochemical biosensor integrating DNAzymes, antifouling magnetic beads, and a hierarchically structured flow cell enables amplification‐ and culture‐free detection directly in stool ...
Survanshu Saxena, Soyeon Lee, Youngeun Choi, Jonathan L'Heureux‐Hache, Jiaying Liu, Sadman Sakib, Sara M. Imani, Marek Smieja, Yingfu Li, Todd Hoare, Leyla Soleymani   +10 more
wiley   +1 more source

Deep Eutectic Solvent‐Enhanced PEDOT: PSS/NR Foam Piezoresistive Sensor for High‐Sensitivity Wearable Devices and Sleep Monitoring Applications

Advanced Materials Interfaces, EarlyView.
A high‐performance piezoresistive foam sensor is developed by integrating natural rubber, PEDOT: PSS, and a deep eutectic solvent (DES). DES effectively detaches insulating PSS from PEDOT, dramatically amplifying electrical conductivity and sensitivity.
Shun Zhang, Jizu Ma, Peng Yu, Lei Tan, Yan Xu   +4 more
wiley   +1 more source

Non-prescription antibiotic dispensing in community pharmacies in jordan: a simulated patient study. [PDF]

Libyan J Med
Bustami M, Abed A, Almazari I, AlQatarneh R, Abu Assab S, Abu Dayyih W, Shilbayeh SAR, Zakaraya Z.   +7 more
europepmc   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Large language model-based simulated patient training for heart failure palliative care communication: a pilot study. [PDF]

Eur Heart J Digit Health
Kishikawa R, Morita H, Kodera S.
europepmc   +1 more source

Programmable Pneumatic Actuator System for a Bioinspired Artificial Colon

Advanced Materials Technologies, EarlyView.
A modular soft robotic colon simulator driven by programmable pneumatic actuation is developed to mimic physiological and pathological‐like motility patterns of the large intestine. Finite element–guided design and distributed control enable anatomically realistic deformation for peristalsis, segmentation, and mass movements, supporting capsule ...
Andrew Bickerdike, Bo Tian, Xizheng Fang, Zepeng Wang, Yang Liu, Lucy Adams, Shyam Prasad   +6 more
wiley   +1 more source

Enhancing System-Level Quality Improvement through Patient-Inclusive Teamwork: A Review

Engaging patients in quality improvement (QI) initiatives offers significant advantages, including increased patient satisfaction, improved outcomes, and the integration of creative insights from patient perspectives.
Mohiuddin, Shaik
core   +1 more source

Delays in the diagnosis and management of pulmonary arterial hypertension: a simulated patient cases study across four European countries. [PDF]

ERJ Open Res
Dardi F, McCullagh B, Ferreira F, Meandzija M, Stulnig G, Neill W, Cruz-Utrilla A.   +6 more
europepmc   +1 more source

A Cryopreservation‐Based Supply Chain Strategy for Extrusion Bioprinting in Space

Advanced Materials Technologies, EarlyView.
Extrusion bioprinting on crewed space platforms requires a bioink that stays functional along the logistic chain. Here, cells and biomaterial ink travel separately, the cells cryopreserved and the ink cold stored, and are combined only minutes before printing.
Johannes Windisch, Max von Witzleben, Richard Frank Richter, Finn Dani, Constantin Greil, Sarah Duin, Anja Lode, Michael Gelinsky   +7 more
wiley   +1 more source