Results 11 to 20 of about 14,949 (308)
Chemometric study of the sinter mixtures used in sinter plants in Poland [PDF]
Metalurgija, 2015 The main goal of the study was the analysis of chemical parameters of sinter mixtures used in sinter plants in Poland. For this purpose the chemometric method was used, in this case hierarchical clustering analysis.
A. Smoliński +2 more
doaj +2 more sources
Harmful admixtures assessment in sinter mixtures used in iron ore sinter plants in Poland [PDF]
Metalurgija, 2014 In this study composition of sinter mixtures used in Polish sinter plants were established. Seven sinter mixtures composition were examined, based on iron-bearing materials, admixtures and fuels.
J. Korol +2 more
doaj +1 more source
Sintering of nanocrystalline materials: Sintering parameters
Heliyon, 2023 Nanostructured materials (NsM) are typical materials with structural length scales of one, two, or three dimensions in the range of 1-100 nm. In the development of NsM, the microstructure of a material, which is an integral factor in determining the intrinsic performance of a material, is susceptible to changes that may hinder the desired nano-state ...
Bukola Joseph Babalola +2 more
openaire +3 more sources
, 2021 This datasets contains Sinter Machine Productivity as out put and 16 input parameters: (1) I/O Fines Total, Fe % (2) I/O Fines SiO2, % (3)I/O Fines Al2O3, % (4)I/O Fines CaO, % (5)Flux CaO, % (6)Flux MgO, % (7)Flux Crushing Index, % (8)Coke Crushing ...
Rath, S (via Mendeley Data) +1 more
core +1 more source
A new powder encapsulation method and its implications on densification by hot isostatic pressing [PDF]
, 1993 Hot isostatic pressing is now an accepted material processing technique for the consolidation of metal powders to near-net-shape components. This thesis examines the use of coatings as in-situ envelopes to overcome the problems associated with ...
Downing, M, Downing, M.
core +3 more sources
Effects of stand-support on the sintering process
工程科学学报, 2016 The load from the upper sinter bed is one of the important factors which deteriorate the permeability of the combustion zone in the sintering process, which restricts the further development of thick bed sintering.
LIU Zheng-jian +4 more
doaj +1 more source
3D Microstructure and Micromechanical Properties of Minerals in Vanadium-Titanium Sinter
High Temperature Materials and Processes, 2019 To investigate the structural characteristics and mechanical properties of minerals in vanadium-titanium sinter, the 3D microstructures of the sinter were reconstructed by serial sectioning in conjunction with computer-aided 3D reconstruction techniques ...
Xu Runsheng +4 more
doaj +1 more source
A review on the production of 17-4PH parts using press and sinter technology
Science Progress, 2023 The press and sinter method remains the standard among powder metallurgy processes for powdered stainless-steel materials. It delivers low cost, low oxidation rate, and adequate corrosion resistance.
Mohammed Qasim Kareem +3 more
doaj +1 more source
Reduction of solid fuel consumption in sintering of Indian iron ore [PDF]
Science of Sintering, 2015 The present investigation deals with the sinterability of Goa (India) iron ore having high Fe (65.2%) content. The sinter basicity (CaO/SiO2) and its MgO were varied in the 2.0 to 2.5 and 1.5 to 3.0 range.
Bhagat R.P.
doaj +1 more source
Journal of Materials Research and Technology, 2019 During iron ore sintering structural transformation occurs as liquid melt is formed in flame front. This study aimed to compare differences in X-ray computed tomography (XCT) measured pore parameters, and examine relationships between pore parameters and
Mingxi Zhou +3 more
doaj +1 more source