Results 21 to 30 of about 4,824 (239)
Materials & Design, 2022 Diamond-like carbon (DLC) coatings deposited on additively manufactured steel greatly improve the tribological properties. However, a high substrate hardness is crucial to sustaining high mechanical loads in the tribological contact.
Wolfgang Tillmann +4 more
doaj +1 more source
The Balance of Titanium and Vanadium in the Blast Furnace with the Use of Sinter Containing a Titanium-Vanadium-Magnetite Concentrate [PDF]
Metalurgija, 2007 The investigation concerned the use of sinter containing a titanium-vanadium-magnetite concentrate for the production of pig iron. Sinter containing 0,46 to 0,51 % TiO2 and 0,056 to 0,060 % vanadium was used for pig iron production in the blast furnace ...
Budzik, R.
doaj
Effects of MgO on the mineral structure and softening-melting property of Ti-containing sinter
工程科学学报, 2018 Certain requirements regarding the chemical composition of slag have to be satisfied to perform a stable blast furnace operation. Particularly, the ratio of MgO to Al2O3 in the slag is observed to have a significant influence on the fluidity and ...
ZHENG An-yang +4 more
doaj +1 more source
Influence of Variable-Diameter Structure on Gas–Solid Heat Transfer in Vertical Shaft Cooler
Metals, 2022 In order to improve the heat transfer between high-temperature sinter and cooling gas in a vertical shaft cooler, a new furnace type with variable-diameter structure was proposed, and the influence of variable-diameter structure on gas–solid heat ...
Tengfei Qi +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh +6 more
wiley +1 more source
Metals, 2023 With the shortage of high-quality coking coal resources and the pursuit of low-cost smelting, the types and sources of coal have changed. Therefore, it is difficult to establish an effective correlation between the existing evaluation indexes of coke ...
Jin Jin, Qi Wang, Song Zhang
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Effect of Furnace Structure on Burden Distribution and Gas Flow in Sinter Vertical Cooling Furnace
Applied Sciences, 2023 Sinter sensible heat recovery via a vertical cooling furnace is a new type of waste heat recovery process proposed based on coke dry quenching. However, the segregation of the burden in a vertical cooling furnace is serious, resulting in a large amount ...
Haifeng Li, Tengfei Qi, Yongjie Zhang
doaj +1 more source
Elinvar Materials: Recent Progress and Challenges
Advanced Engineering Materials, EarlyView.Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley +1 more source