Results 101 to 110 of about 530,053 (388)

Removal of 2,4-Dichlorophenoxyacetic Acid from Aqueous Solutions Using Al₂O₃/Graphene Oxide Granules Prepared by Spray-Drying Method

Resources
Within this study, aluminum oxide granules with 0.25%vol. of graphene oxide were prepared by a spray-drying method to make an adsorbent for the 2,4-Dichlorophenoxyacetic acid (2,4-D) herbicide removal from aqueous solutions.
Alexandra Yu. Kurmysheva, Ekaterina Kuznetsova, Marina D. Vedenyapina, Pavel Podrabinnik, Nestor Washington Solís Pinargote, Anton Smirnov, Sergey N. Grigoriev   +6 more
doaj   +1 more source

Fabrication of conformal array patch antenna using silver nanoink printing and flash light sintering

AIP Advances, 2018
The sintering process constitutes an important part of the conductive-pattern inkjet printing process, as it directly affects the conductivity of the conductive pattern.
Fanbo Meng, Jin Huang
doaj   +1 more source

Single‐Crystal Castability of CM186LC Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The optimal conditions to obtain single‐crystal (SX) castings of the directional solidification nickel‐based superalloy CM186LC, are investigated. Cylindrical samples are cast via a proprietary SX Bridgman process. The effect of solidification rates (V) ranging from 1 to 10 mm⋅min−1 on the microstructure is explored.
André Baldissera, Sean Böhm, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

3Y-TZP/Ta Biocermet as a Dental Material: An Analysis of the In Vitro Adherence of Streptococcus Oralis Biofilm and an In Vivo Pilot Study in Dogs

Antibiotics
The surface adhesion of bacterial cells and the in vivo biocompatibility of a new ceramic–metal composite made of zirconium dioxide and tantalum were evaluated.
Anton Smirnov, Oleg Yanushevich, Natella Krikheli, Nestor Washington Solis Pinargote, Pavel Peretyagin, Sergey Grigoriev, Luis Alou, David Sevillano, Roberto López-Piriz, Francisco Guitian, José Florindo Bartolomé   +10 more
doaj   +1 more source

Master sintering curves of two different alumina powder compacts [PDF]

Processing and Application of Ceramics, 2009
Concept of Master Sintering Curve is a strong tool for optimizing sintering schedule. The sintering behaviour can be predicted, and sintering activation energy can be calculated with the help of few dilatometric measurements.
Vaclav Pouchly, Karel Maca
doaj  

Amorphous Al-Ti Powders Prepared by Mechanical Alloying and Consolidated by Electrical Resistance Sintering [PDF]

, 2019
A novel processing method for amorphous Al50Ti50 alloy, obtained by mechanical alloying and subsequently consolidated by electrical resistance sintering, has been investigated.
Caballero Sánchez, Eduardo, Gómez Cuevas, Francisco de Paula, Montes Martos, Juan Manuel, Nandyala, Sooraj, Ternero Fernández, Fátima, Urban, Petr   +5 more
core   +2 more sources

Direct In Situ TEM Visualization and Insight into the Facet-Dependent Sintering Behaviors of Gold on TiO2.

Angewandte Chemie, 2018
Preventing sintering of supported nanocatalysts is an important issue in nanocatalysis. A feasible way is to choose a suitable support. However, whether the metal-support interactions promote or prevent the sintering has not been fully identified.

semanticscholar   +1 more source

Surface Modification of Sol–Gel Synthesized Ba0.85Ca0.15Zr0.1Ti0.9O3 using Stearic Acid Additives

Advanced Engineering Materials, EarlyView.
This study explores a novel approach to enhance the piezoelectric performance of lead‐free BCZT ceramics synthesized via the sol–gel method. By coating the BCZT powder with only a 0.69 nm stearic acid layer, the electromechanical response is significantly boosted up to 359 pC N−1, revealing promising implications for high‐performance sensor and ...
Michelle Weichelt, Maria Rita Cicconi, Isabella Klösel, Swantje Funk, Alexander Martin, Ken‐ichi Kakimoto, Tobias Fey   +6 more
wiley   +1 more source

Mechanical properties variation of samples fabricated by fused deposition additive manufacturing as a function of filler percentage and structure for different plastics

Scientific Reports
One of the key factors in manufacturing products by fused deposition molding (FDM) or layer-by-layer printing technology is the material intensity of the product.
Sergey Grigoriev, Nikita Nikitin, Oleg Yanushevich, Natella Krikheli, Roman Khmyrov, Daniil Strunevich, Mihail Soloninkin, Nestor Washington Solis Pinargote, Pavel Peretyagin, Anton Smirnov   +9 more
doaj   +1 more source

Material Issues of the Metal Printing Process, MPP [PDF]

, 2006
The metal printing process, MPP; is a novel Rapid Manufacturing process under development at SINTEF and NTNU in Trondheim, Norway. The process, which aims at the manufacturing of end-use products for demanding applications in metallic and CerMet ...
Boivie, K., Karlsen, R., Van der Eijk, C.   +2 more
core   +1 more source