Results 111 to 120 of about 20,341 (299)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Influence of slenderness ratio on the structural performance of lightweight foam concrete composite panel

Case Studies in Construction Materials, 2019
In this research paper is reported the analytical and experimental investigations on the influence of slenderness ratio on the structural performance of lightweight foam concrete composite panel (LFCCP).
Y.H. Mugahed Amran, Rayed Alyousef, Hisham Alabduljabbar, Fahed Alrshoudi, Raizal S.M. Rashid   +4 more
doaj   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source

Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones

Advanced Engineering Materials, EarlyView.
A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell, Martha Leach, Hongtao Song, Carolyn Seepersad   +3 more
wiley   +1 more source

PERFORMANCE OF A SINGLE PILE UNDER COMBINED AXIAL AND LATERAL LOADS IN LAYERED SANDY SOIL

Journal of Engineering and Sustainable Development, 2018
A combination of axial and lateral was applied on a small scale model piles embedded in layered sand soil. Two types of piles were used (open and closed ended steel box piles), while the relative density (Dr) of the upper and lower sand layers were ...
Saad Farhan Ibrahim, Madhat Shakir Al-Soud, Fawaz Ibrahim Al-Asadi   +2 more
doaj  

Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere

Advanced Engineering Materials, EarlyView.
A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

INVESTIGATION OF THE EFFECT OF SLENDERNESS RATIO ON THE STRUCTURAL RESPONSE OF MASONRY MINARETS

Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi, 2020
Recent large earthquakes (eg, the Mw7.2, 2011 Van, Turkey, earthquake and the Mw6.6, 2017 Mugla, Turkey, earthquake) have shown that the vulnerability of slender masonry minarets under seismic loadings . The response of minarets to seismic excitations are different from other form structures because of their complex behavior due to geometrical changes ...
openaire   +3 more sources

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source