Results 121 to 130 of about 20,341 (299)
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Size And High Temperature Effects On The Compressive Strength Of Self Compacting Concretes [PDF]
, 2013 The compressive strength behavior of concrete is one of the fundamental parameters of structural design as most load-bearing concrete elements, such as beams, columns and slabs.
Anwar Hossain +4 more
core
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
Stability and bifurcation Problems for Equilibrium States of a Liquid Bridge [PDF]
, 1994 The results of an investigation on the stability of a doubly connected axisymmetric equilibrium free surface pinned to the edges of two coaxial disks are presented.
Perales Perales, José Manuel +1 more
core +1 more source
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Comparison of uniform perturbation solutions and numerical solutions for some potential flows past slender bodies [PDF]
Approximate solutions for potential flow past an axisymmetric slender body and past a thin airfoil are calculated using a uniform perturbation method and then compared with either the exact analytical solution or the solution obtained using a purely ...
Geer, J., Liu, C. H., Wong, T. C.
core +1 more source
Rigorous derivation of the formula for the buckling load in axially compressed circular cylindrical shells [PDF]
, 2014 The goal of this paper is to apply the recently developed theory of buckling of arbitrary slender bodies to a tractable yet non-trivial example of buckling in axially compressed circular cylindrical shells, regarded as three-dimensional hyperelastic ...
Grabovsky, Yury, Harutyunyan, Davit
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Behaviour of concrete filled stainless steel elliptical hollow sections [PDF]
, 2008 This paper presents the behaviour and design of axially loaded concrete filled stainless steel elliptical hollow sections. The experimental investigation was conducted using normal and high strength concrete of 30 and 100 MPa. The current study is based
Burdett, M., Gardner, L., Lam, D.
core
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source