Results 71 to 80 of about 67,714 (263)
Remote Sensing, 2016 The Altyn Tagh Fault (ATF) is one of the major left-lateral strike-slip faults in the northeastern area of the Tibetan Plateau. In this study, the interseismic deformation across the ATF at 85°E was measured using 216 interferograms from 33 ENVISAT ...
Sen Zhu +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
Applied SciencesGNSS technology utilizes satellite signals to determine the position of a point on Earth. Using this location information, the GNSS velocities of the points can be calculated.
Halil İbrahim Solak
doaj +1 more source
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
Remote SensingAsymmetric deformation has been observed along the Altyn Tagh Fault (ATF), the northern boundary of the Tibetan Plateau. Several mechanisms have been proposed to explain this asymmetry, including contrasts in crustal strength, lower crust/upper mantle ...
Yi Luo +4 more
doaj +1 more source
Effect of surface roughness on rate-dependent slip in simple fluids [PDF]
The Journal of Chemical Physics, 2007 Molecular dynamics simulations are used to investigate the influence of molecular-scale surface roughness on the slip behavior in thin liquid films. The slip length increases almost linearly with the shear rate for atomically smooth rigid walls and incommensurate structures of the liquid/solid interface.
openaire +5 more sources
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
SeismicaSurface ruptures appear over a wide area in addition to the primary fault during a Large earthquake like the 2016 Kumamoto earthquake. Although the displacement of such distributed surface ruptures is small, information on their paleo activities provides
Daisuke Ishimura +5 more
doaj +1 more source
On design of worm gears with cylindrical worms
Advanced Engineering Research, 2016 The work objective is to introduce the visualization of the project main parameters into the design methodology to accelerate the adoption of constructive solutions while maintaining the geometric dimensions accuracy and their reference to the technical ...
Yury P. Manshin, Elena Y. Manshina
doaj +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source