Results 51 to 60 of about 130,989 (297)
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Study of the slippage of particle / supercritical CO2 two-phase flow [PDF]
, 2016 In this paper, the slippage velocity and displacement between particles and supercritical CO2 (SC-CO2) were studied to reveal the particle-SC-CO2 two-phase flow behavior.
Geng, Xueyu +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Optimum Winding Tension and Nip-load into Wound Webs for Protecting Wrinkles and Slippage
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2010 This paper describes the novel optimization method of wind-up tension to prevent wound roll defects, mainly star defect (wrinkling) and telescoping (slippage), based on the optimum design technique.
Hiromu HASHIMOTO +2 more
doaj +1 more source
Deformations of thick two-material cylinder under axially varying radial pressure [PDF]
, 1976 Stresses and deformations in thick, short, composite cylinder subjected to axially varying radial pressure are studied. Effect of slippage at the interface is examined.
Patel, Y. A.
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Power circulation in driveline system when the wheels of tractor and trailer are driven
Transport, 2013 In off-road “tractor–trailer” vehicle combinations, the trailer can be equipped with one or more driving wheels. The distinguishing feature of vehicles with two or more driving axles is distribution of total power between the driving wheels.
Algirdas Janulevičius +1 more
doaj +1 more source
PERFORMANCE OF CORN SOWING IN FERTILIZATION SYSTEM AND INTERCROPPING [PDF]
Engenharia Agrícola, 2018 The performance of the tractor-seeder can be influenced by factors related to the seeder, as loads and crop. The aim of the present study was to evaluate the performance of tractor-seeder at sowing in the corn crop in function of the fertilizer systems ...
Jorge W. Cortez +3 more
doaj +1 more source
Deep Saturated Free Electron Laser Oscillators and Frozen Spikes [PDF]
, 2016 We analyze the behavior of Free Electron Laser (FEL) oscillators operating in the deep saturated regime and point out the formation of sub-peaks of the optical pulse. They are very stable configurations, having a width corresponding to a coherence length.
Biedron, S. +7 more
core +5 more sources