Results 71 to 80 of about 577,675 (243)

Erosive wear response of SiCp reinforced aluminium based metal matrix composite: Effects of test environments

Journal of Mechanical Engineering and Sciences, 2017
In the present investigation, the erosive wear behaviour of a 10 wt.% SiC particles reinforced aluminium based metal matrix composite has been studied. The composite was fabricated by dispersing SiC particles of size 50-100 µm into the matrix alloy. The
M.M. Khan, Gajendra Dixit
doaj   +1 more source

Microstructure, hardness and slurry erosion-wear behaviors of high-speed laser cladding Stellite 6 coatings prepared by the inside-beam powder feeding method

Journal of Materials Research and Technology, 2022
Ziyi Yang, Yongxin Jian, Zihan Chen, Hongjun Qi, Zhifu Huang, Guosheng Huang, J. Xing   +6 more
semanticscholar   +1 more source

Erosion of materials by alumina slurry

, 1989
An examination of the erosion resistance of materials utilized in the construction of alumina pumps was carried out. This included laboratory research and, for the purpose of verification, investigation under actual service conditions. In this paper the effect of material properties on erosion resistance is considered. In the second paper the influence
Lou, Hong Qing, Križman, Alojz
openaire   +1 more source

Effect of Slurry Concentration on Simultaneous Damage of Cavitation Erosion and Slurry Wear.

TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A, 2001
Simultaneous damage of cavitation erosion, and slurry wear of SUS 304 was studied by using a test apparatus with the combination of an ultrasonic vibratory cavitation device and a slurry jet device. The tests were carried out in slurry having concentrations from 0 mass percent to 6 mass percent. The slurry was made of tap water and silica sand.
HATTORI, Shuji, MAEKAWA, Norihide
openaire   +2 more sources

Comparative Study of Jet Slurry Erosion of Martensitic Stainless Steel with Tungsten Carbide HVOF Coating

Metals, 2019
This work evaluates the behavior of a martensitic stainless steel (AISI 410) thermally treated by quenching and tempering with a tungsten carbide (86WC-10Co-4Cr) coating obtained by high-velocity oxygen fuel (HVOF) thermal spray deposition, analyzing the
Galileo Santacruz, Antonio Shigueaki Takimi, Felipe Vannucchi de Camargo, Carlos Pérez Bergmann, Cristiano Fragassa   +4 more
doaj   +1 more source

Slurry erosion wear of high chromium cast iron samples from a slurry pump impeller. Effect of impact angle variation [PDF]

, 2023
Renato Chaves Pereira da Silva, Paulo Ricardo Barbosa, J.J. Penagos, Rodrigues da Costa Adilson   +3 more
openalex   +1 more source

Slurry Erosion-Corrosion Characteristics of As-Built Ti-6Al-4V Manufactured by Selective Laser Melting. [PDF]

Materials (Basel), 2020
Aldahash SA, Abdelaal O, Abdelrhman Y.
europepmc   +1 more source

High-velocity oxy-fuel and high-velocity air fuel sprayed WC-Co-Cr coatings on solution-treated 21-4N steel for slurry and corrosion resistance

Journal of Electrochemical Science and Engineering
This study aims to fabricate WC-Co-Cr coatings on the solution-treated 21-4N steel utilizing high-velocity oxy-fuel (HVOF) and high-velocity air fuel (HVAF) techniques.
Rajanna Lingappa, Tumakur Gangadhar Mamatha, Momballi Shivappadevaru Prabhuswamy, Vikrant Singh, Anuj Bansal   +4 more
doaj   +1 more source

Effect of impact angle on the slurry erosion-corrosion of Stellite 6 and SS316 [PDF]

, 2014
Nicola Andrews, L. Giourntas, Alexander Galloway, A. Pearson   +3 more
openalex   +1 more source

Evaluation of surface strength of thin hard coating by micro slurry-jet erosion (MSE) and fine particles erosion method with impact particles of various size

, 2020
Tatsuki YAMASHITA, Toshiro MIYAJIMA, Noriyo HORIKAWA, Daichi SATOMI, Shingo KAWAMURA   +4 more
openalex   +1 more source