Results 11 to 20 of about 4,430,869 (300)
Development of Direct Reduction Process and Smelting Reduction Processes for the Steel Production [PDF]
Kemija u Industriji, 2006 Although the blast furnace and basic oxygen furnace are going to be primary routes for steel production in future, the steelmaking industry using the electric arc furnace route will continue to grow.
Kožuh S., Gojić M.
doaj +4 more sources
Feasibility of nickel extraction from Indian chromite overburden by solid state reduction and smelting route [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2020 The present work demonstrates the extraction of nickel from low-grade chromite overburden by using solid state reduction and direct smelting route. Goethite & Quartz are present as major phases whereas chromite, hematite were identified as minor phases ...
Ganesh P. +5 more
doaj +1 more source
Metals, 2023 To determine slag properties and the factors influencing these properties for optimization of operating conditions in the copper flash smelting process, the composition and microstructures of the quenched smelting and converting slags have been analyzed.
Sui Xie +3 more
doaj +1 more source
Impact of Iron Ore Pre-Reduction Degree on the Hydrogen Plasma Smelting Reduction Process
Metals, 2023 To counteract the rising greenhouse gas emissions, mainly CO2, the European steel industry needs to restructure the current process route for steel production.
Daniel Ernst +4 more
semanticscholar +1 more source
Steel Research International, 2023 Reducing greenhouse gases (GHG), especially CO2, is necessary to counteract climate change. The European steel industry currently corresponds to 5.7% of the total EU emissions and must therefore minimize their GHG fractions in the future. One of the most
Daniel Ernst +3 more
semanticscholar +1 more source
Study on hydrogen smelting reduction behaviour in synthetic molten HIsarna slag
Ironmaking & Steelmaking, 2023 The reduction behaviour of hydrogen with FeO in synthetic molten HIsarna slag has been investigated using two experimental methods: (1) Blowing 5% or 10% H2-Ar onto the molten slag at 1450°C, 1475°C, 1550°C, respectively; and (2) Injecting 10% H2-Ar into
Theint Theint Htet +5 more
semanticscholar +1 more source
Experimental Study on Lead-Smelting Slag as Paste Filling Cementing Material
Geofluids, 2022 Under the current pressure of mineral product price and market competition, as well as the tightening of ecological and environmental protection policies, energy saving, emission reduction and cost reduction, and efficiency increase have become ...
Daiqiang Deng, Guodong Cao, Yihua Liang
doaj +1 more source
Recovery of Cu-Fe Alloy from Copper Smelting Slag
Metals, 2023 Copper smelting slag usually contains 1–6 wt% copper, which can be recovered by pyrometallurgical and flotation processes. However, the tailing slags still consist of 0.3–0.7 wt% Cu and 35–45 wt% Fe equivalents to those in the copper and iron ores ...
Yi Qu, Keqin Tan, Baojun Zhao, Sui Xie
doaj +1 more source
Industrial test of smelting reduction for manganese ore in converter
工程科学学报, 2022 The smelting reduction of manganese ore in the converter has been reported in China since the 1990s, and some steel enterprises have successively carried out industrial tests of this technology.
Lu LIN +7 more
doaj +1 more source
Smelting separation behaviors and mechanisms of high-alumina rich-manganese ore obtained from metallic reduction and magnetic separation [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2019 In this paper the smelting separation of high-alumina rich-manganese ore prepared with selective reduction and magnetic separation was proposed to produce the high carbon ferromanganese alloy (HCFeMn). The rational smelting separation parameters for high-
Gao L.-H., Liu Z.-G., Chu M.-S.
doaj +1 more source