Results 111 to 120 of about 42,269 (256)
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
The art gallery as a place to foster a sense of social identity
Technical TransactionsThe article presents the results of sociological research, which were taken into account in the selection of means of architectural shaping of the architecture of art galleries.
Sowa Aleksandra, Gosztyła Marek
doaj +1 more source
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This work explores the reduction of nickel oxide layers using dielectric barrier discharge plasma in an argon–hydrogen atmosphere. The results reveal a strong temperature dependence, enabling complete reduction of thick oxide layers at 200°C within seconds.
Maria Argirusi +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Effects of an online group dance programme on adolescents’ social bonding and wellbeing
, 2023 Tuncgenc B, Greig E, Cohen E.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source