Results 111 to 120 of about 1,903,453 (290)

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar   +3 more
wiley   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

open access: yesAdvanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon   +3 more
wiley   +1 more source

High-Frequency Flow Rate Determination—A Pressure-Based Measurement Approach

open access: yesJournal of Experimental and Theoretical Analyses
Accurate flow measurement is critical for hydraulic systems because it represents a crucial parameter in the control of fluid power systems and enables the calculation of hydraulic power when combined with pressure data, which is valuable for ...
Faras Brumand-Poor   +4 more
doaj   +1 more source

A Single-Wire Soft Sensor for Seamless Multimodal Tactile Sensing [PDF]

open access: yes
Integrating sensing in a soft robot is still crucial to enable feedback response to environmental stimuli. This paper presents a single-wire soft sensor for multimodal tactile sensing designed to address the limitations of current technologies.
Visentin, Francesco, Meneghetti, Matteo
core   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

open access: yesAdvanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe   +9 more
wiley   +1 more source

A Low-Cost Soft Coiled Sensor for Soft Robots

open access: yes, 2016
Soft robots made from soft materials can closely emulate biological system using simple soft mechanical structures. Compared with traditional rigid-link robots, they are safe to work with humans and can adapt to confined environments.
Jianguo Zhao, Ali Abbas
core   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

open access: yesAdvanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo   +15 more
wiley   +1 more source

Design and fabrication of integrated soft sensor for soft gripper using multi-material 3D printing

open access: yes, 2023
In the field of soft robotics, integration of sensors into soft, flexible grippers poses significant challenges due to their high-dimensionality and the complexities in developing soft sensors.
Li, Xin
core  

Gyroid Structured Globugraphite Carbon Foam With Hierarchical and Tailored Pore Size

open access: yesAdvanced Engineering Materials, EarlyView.
Secondary sacrificial templates were designed and printed to create a defined network within a porous carbon. Lattices thermally degrades during the sintering process. Lattices are imprinted into the ceramic template and transferred to the morphology of Globugraphite.
Christiane Roller   +6 more
wiley   +1 more source

Microstructural, Mechanical, and Textural Evolution of Dissimilar Combination of Laser‐Welded Maraging Steel and 4340 Steel

open access: yesAdvanced Engineering Materials, EarlyView.
The present work reports the microstructural, mechanical, and texture evolution of a dissimilar combination laser‐welded maraging steel with 4340 steel. This is important for aerospace applications. The demand for dissimilar welding is growing rapidly with the requirement of efficient and durable joints.
Bharat Behl   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy