Results 231 to 240 of about 58,770 (304)

Anti-Biofouling Coatings Based on Ultra-Slippery Surfaces. [PDF]

Cell Biol Int
Tesler AB, Goldmann WH.
europepmc   +1 more source

Characterization of Fuel Rods Supported by Dimple‐Less Spacer Grids and Subjected to Nonlinear Vibrations

International Journal of Mechanical System Dynamics, EarlyView.
ABSTRACT An experimental campaign was undertaken to demonstrate the applicability of the Bouc–Wen hysteretic model to describe the hysteretic system of the recent Framatome dimple‐less spacer grid design for Pressurized Water Reactors. The experimental setup subjected a reduced‐length fuel rod, supported at both ends by dimple‐less grids, to forced ...
Giovanni Ferrari, Brian Painter, Kostas Karazis, Marco Amabili   +3 more
wiley   +1 more source

A Comprehensive Study of the Effect of Lubricant in the Sizing Agent on the Properties of a Basalt Fiber and Epoxy Resin Composite Material. [PDF]

Nanomaterials (Basel)
He J, Lai C, Li J, Yang N, Xie B, Li X, Deng Y, Zou L.   +7 more
europepmc   +1 more source

Systematic Parameter Selection for Short Fiber Polymer Composite Direct Fiber Simulation

Polymer Composites, EarlyView.
Interactions of individually simulated fibers are systematically calibrated such that their orientation history agrees with the results from analytical orientation models. ABSTRACT The orientation of fibers in short discontinuous fiber reinforced polymer composites is a critical factor in determining final mechanical and thermal properties.
Jason B. Pierce, Douglas E. Smith
wiley   +1 more source

Stress-Dependent Permeability of Porous Polyimide Under Stress Loading and Unloading. [PDF]

ACS Omega
Xu R, Shen D, Wang L, Bao M, Zhao X, Wang W.   +5 more
europepmc   +1 more source

Exploring the Tribological Properties of 3D Printed Polymer Composites: An Experimental Study

Polymer Composites, EarlyView.
Tribological pin‐on‐disc testing of FDM‐manufactured pins. Pins made from PLA, TPU, bronze‐filled PLA (BRO), and their combinations were tested against a SAE 1020 steel disc to evaluate friction, wear, and surface morphology. ABSTRACT In recent years, additive manufacturing, especially 3D printing, has been gaining more space in the production of parts
G. Lasch, G. G. Sostizzo, G. S. Gehlen, M. T. Birosz, M. Andó, R. H. S. Souza, A. A. Rodrigues, J. C. Poletto, L. Y. Barros, N. F. Ferreira, P. D. Neis   +10 more
wiley   +1 more source

Advances in the Tribological Performance of Graphene Oxide and Its Composites. [PDF]

Materials (Basel)
Wakchaure MB, Menezes PL.
europepmc   +1 more source

Solid Particle Erosion and Predictive Modeling of Epoxy Composites Reinforced With Diatom Frustules

Polymer Composites, EarlyView.
Schematic representation of the solid particle erosion process and predictive modeling workflow for diatom frustule‐reinforced epoxy composites, illustrating the test setup, erosion response curve, and filler‐matrix interaction. ABSTRACT This study examines the solid particle erosion wear behavior of epoxy composites reinforced with 5–20 wt% calcined ...
Elif Gültürk, Eser Yarar, Orkan Baran Korkusuz, Aleyna Kara, Tamer Sınmazçelik   +4 more
wiley   +1 more source

Ocular bio-lubricating materials: from lubrication mechanism to dry eye syndrome treatment. [PDF]

Regen Biomater
Zhang Y, Ding S, Wang X, Li J, Yu H, Lin W.   +5 more
europepmc   +1 more source

Modeling Fiber Dispersion in a Single‐Screw Extruder for Long Fiber‐Reinforced Thermoplastics

Polymer Composites, EarlyView.
Fiber dispersion throughout the screw channel ABSTRACT Understanding the mechanics of fiber attrition during the plasticizing process is important in predicting the strength of long fiber‐reinforced thermoplastics (LFT) composites. Fiber dispersion has been found to impact fiber damage during processing and therefore final fiber length in the final ...
Hector Sebastian Perez, Paula Hohoff, Florian Hiller, Angel Yanev, Tim Osswald   +4 more
wiley   +1 more source