Results 161 to 170 of about 619,940 (356)

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Nitride‐Reinforced Metal Matrix Nanocomposite Powders Production by Plasma‐Assisted Thermochemical Treatment of Intermetallic Powders

Advanced Engineering Materials, EarlyView.
This study proposes a new methodology for producing metal matrix nanocomposites in the solid state. The process involves the plasma‐assisted thermochemical treatment of metallic alloy powders. As a proof‐of‐concept, TiN nanoparticles are synthesized directly on the surface of FeTi intermetallic powder particles, enabling the development of the ...
Deivison Daros Paim, Antônio Rogério de Souza, Tatiana Bendo, Aloisio Nelmo Klein, Rodrigo Perito Cardoso   +4 more
wiley   +1 more source

Bimetallic (NiFe) and Trimetallic (NiFeCr) Nanoalloys from Metal Oxides Using a Microwave Hydrogen Plasma

Advanced Engineering Materials, EarlyView.
Bimetallic (NiFe) and trimetallic (NiFeCr) nanoalloys (NAs) are synthesized using corresponding oxide mixtures using microwave hydrogen plasma within a few milliseconds. The process simultaneously 1) reduces metal oxides to metals; 2) downsizes the particles from micrometers to nanometers; and 3) blends the metals to form NAs.
Sachin Kumar, Mohammad Kazemi, Zichang Xiong, Thomas Cameron, Julian Held, Uwe Kortshagen   +5 more
wiley   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

A high voltage gain solid-state transformer for integration of renewable energy and AC sources. [PDF]

Sci Rep
Hashemzadeh SM, Al-Hitmi MA, Islam S, Iqbal A, Aghaei H, Hosseini SH, Babaei E.   +6 more
europepmc   +1 more source

Removing Homocoupling Defects in Alkoxy/Alkyl‐PBTTT Enhances Polymer:Fullerene Co‐Crystal Formation and Stability

Advanced Functional Materials, EarlyView.
PBTTT‐OR‐R, a C14‐alkoxy/alkyl‐PBTTT polymer derivative, is of substantial interest for optoelectronics due to its specific fullerene intercalation behavior and enhanced charge‐transfer absorption. Comparing this polymer with (S) and without (O) homocoupling defects reveals that PBTTT‐OR‐R(O) forms stable co‐crystals with PC61BM, while PBTTT‐OR‐R(S ...
Zhen Liu, Jochen Vanderspikken, Paola Mantegazza, Stefania Moro, Mouna Hamid, Sigurd Mertens, Niko Van den Brande, Laurence Lutsen, Vincent Lemaur, David Beljonne, Giovanni Costantini, Koen Vandewal, Bruno Van Mele, Wouter Maes, Bart Goderis   +14 more
wiley   +1 more source

Enhancing Efficiency in Coal-Fired Boilers Using a New Predictive Control Method for Key Parameters. [PDF]

Sensors (Basel)
Li Q, Yu L, Liu T, Li L, Lin Y, Wang T, Yang C, Wang L, Weng W, Zheng C, Gao X.   +10 more
europepmc   +1 more source