Results 151 to 160 of about 2,532,106 (293)

Recent Advances in Plasma‐Enhanced Atomic Layer Etching for Next‐Generation Nanofabrication

Advanced Materials Interfaces, EarlyView.
Continued semiconductor miniaturization demands atomic‐scale patterning and ultralow surface roughness beyond the capabilities of conventional reactive ion etching. This review highlights advances in isotropic and anisotropic plasma‐enhanced atomic layer etching since 2020, covering fundamental mechanisms, applications across major semiconductor ...
Shih‐Nan Hsiao
wiley   +1 more source

Tracking interlinked microbial and geochemical succession over decades in landfilled municipal solid waste. [PDF]

Appl Environ Microbiol
Munford KE, Grégoire DS, Hug LA.
europepmc   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

Release characteristics of NH₃ and VOCs during short-term fermentation of municipal solid waste. [PDF]

RSC Adv
Hu J, Gong D, Xia H, Yang L, Dong C, Zhong H, Xie Y, Jian Z.   +7 more
europepmc   +1 more source

DRAFT: Solid waste management state plan update, 1993-2002

, 1993
Section I: Municipal and Industrial Solid Waste (January 1993); Section II: Comprehensive Regulated Medical Waste Management Plan (April 1993); Section III: Statewide Sludge Management Plan Update (September ...
New Jersey. Department of Environmental Protection and Energy. Division of Solid Waste Management
core  

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

A systematic analytical framework for multi-source municipal solid waste characterization for energy recovery. [PDF]

MethodsX
Nabulime MN, Li Y, Wang Z, Ding L, Yu Z, Yu F, Ge X, Chuenchart W, Lansing S.   +8 more
europepmc   +1 more source

Municipal Solid Waste Performance Indicators

, 2009
Não disponível ainda. (Eduardo Oliveira, 2009-10-16)Não disponível ainda. (Eduardo Oliveira, 2009-10-16)111Não disponível ainda.
Almeida, M. C., Neves, E. B.
core  

Eutectic Gallium‐Indium as a Potential Non‐Toxic Replacement in Mercury Intrusion Porosimetry

Advanced Materials Technologies, EarlyView.
A practical alternative to mercury intrusion porosimetry is presented using non‐oxidized eutectic gallium‐indium. An eGaIn Filling Station enables oxygen‐free preparation of standard penetrometers, and the resulting measurements faithfully reproduce pore‐size distributions and intrusion volumes measured with mercury across several standard reference ...
Denis Schuetz, Michael F. Noisternig, Manuel Brandstaetter, Valentin Seyfried, Norbert Reitinger, Bernhard Nell, Alexander Kasper, Riaz Ahmad, Martin Thomas   +8 more
wiley   +1 more source

Optimization of Recycled Fine Aggregate Content for All-Solid-Waste-Based Flowable Solidified Soil: Performance and Microstructure. [PDF]

Materials (Basel)
Wang A, Ju L, Ni J, Li L, Zhen E.
europepmc   +1 more source