Results 131 to 140 of about 5,167,248 (342)

Effect of length of Handley Page tip slots on the lateral-stability factor, damping in roll [PDF]

Tests have been made in the NACA 7 by 10 foot wind tunnel on a Clark Y wing model equipped with various lengths of Handley Page slots extending inward from the wing tips. The slot lengths tested ranged from 20 to 100 per cent of the semi span. The effect
Weick, Fred E, Wenzinger, Carl J
core   +1 more source

Unsteady flow, clusters and bands in a model shear-thickening fluid

, 2019
We analyse the flow curves of a two-dimensional assembly of granular particles which are interacting via frictional contact forces. For packing fractions slightly below jamming, the fluid undergoes a large scale instability, implying a range of stress ...
Grob, Mathias, Heussinger, Claus, Saw, Shibu, Zippelius, Annette   +3 more
core   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Size scaling of strength in thin film delamination

, 2011
We investigate by numerical simulation the system size dependence of the shear delamination strength of thin elastic films. The films are connected to a rigid substrate by a disordered interface containing a pre-existing crack. The size dependence of the
Alava M J, Bazant Z P, M Zaiser, Zaiser M, Zaiser M   +4 more
core   +1 more source

Elinvar Materials: Recent Progress and Challenges

Advanced Engineering Materials, EarlyView.
Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

APPLICATION OF GFRP SHEET FOR STRENGTHENING OF YIELDED REINFORCED CONCRETE BEAMS [PDF]

The use of fiber reinforced polymer (FRP) by the civil engineering community spans more than two decades. It has been applied to many purposes for civil engineering structures not only for new structures but also for strengthening of the deteriorated ...
Djamaluddin, Rudy
core  

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley   +1 more source