Results 91 to 100 of about 228 (170)

Assessment of Monomer Release From Resin Composites Following the Use of Various Modeling Liquids

Journal of Esthetic and Restorative Dentistry, EarlyView.
ABSTRACT Objectives The chemical composition of resin composites and the use of modeling liquids may influence the release of residual monomer, potentially impacting biocompatibility. This in vitro study evaluated the effect of different modeling liquids on the elution of monomers from two resin composites.
Dorukcan Yıldırım, Hüseyin Hatırlı, Emine Şirin Karaarslan, Tarık Balkan   +3 more
wiley   +1 more source

Wettability of saliva substitutes across various denture base fabrication techniques

Journal of Prosthodontics, EarlyView.
Abstract Purpose The present study evaluated the contact angles (CAs) of four denture base materials subjected to different surface treatments using deionized water and saliva substitutes. Material and Methods A total of 32 rectangular specimens were manufactured using four different denture base materials: heat‐cured compression molded Lucitone 199 (C)
Paul Mikhail, Igor Pesun, Francisco Azpiazu‐Flores, Rodrigo França   +3 more
wiley   +1 more source

Circulating purification of cutting fluid: an overview. [PDF]

Int J Adv Manuf Technol, 2021
Wu X, Li C, Zhou Z, Nie X, Chen Y, Zhang Y, Cao H, Liu B, Zhang N, Said Z, Debnath S, Jamil M, Ali HM, Sharma S.   +13 more
europepmc   +1 more source

Mitochondrial Ca2+ uniporter haploinsufficiency leads to sexually dimorphic redox imbalance and metabolic remodelling in the mouse brain

The Journal of Physiology, EarlyView.
Abstract figure legend The genetic inactivation of one Mcu allele leads to sex‐specific changes in neuronal function in adult mice, that is, the firing of action potentials and the relationship between cytosolic and mitochondrial Ca2+ levels. The ability to produce NAD(P)H by stimulated neural tissue is largely preserved in male mice but delayed in ...
Jenna Gray, Girish Halemirle, Beatriz Ferrán, Hadyn Rose, Traci L. Redwine, Sophia Pham, Bo Hagy, Atul Pranay, Jennifer Giorgione, Stacy A. Hussong, Veronica Galvan, Kenneth Humphries, Holly Van Remmen, Mike Kinter, William E. Sonntag, Pankaj K. Singh, Carlos Manlio Díaz‐García   +16 more
wiley   +1 more source

A Systematic Review on Carbon Nanotube- and Graphene Nanoplatelet-Reinforced Plasma-Sprayed Alumina-Based Hybrid Nanocomposite Coatings. [PDF]

ACS Omega
Pandey KK, Ganvir A.
europepmc   +1 more source

Dynamics of an impacting emulsion droplet. [PDF]

Sci Adv, 2022
Damak M, de Ruiter J, Panat S, Varanasi KK.   +3 more
europepmc   +1 more source

Concept, Tests, and Optimum Design of Novel Negative Stiffness Friction Dampers for Seismic Protection of Long‐Span Bridges

Earthquake Engineering &Structural Dynamics, Volume 55, Issue 11, Page 2719-2741, September 2026.
ABSTRACT Viscous dampers (VDs) are widely used to mitigate the excessive responses of long‐span bridges. However, VDs face some intricate challenges in engineering practices, including high damping coefficient requirement, potential base shear amplification and tremendous damping force under high velocity. To address these issues, this study develops a
Ruisheng Ma, Shaodong Jiang, Kun Xu, Qiang Han, Xiuli Du, Kaiming Bi   +5 more
wiley   +1 more source

Transmission ratio-efficiency coupled modeling and high-efficiency zone design for multi-row planetary gear transmission of hybrid electric vehicles. [PDF]

Sci Rep
Zhang Q, Ren C, Niu H.
europepmc   +1 more source

Effects of lubricant-fuel mixing on particle emissions in a single cylinder direct injection spark ignition engine. [PDF]

Sci Rep, 2022
Yi H, Seo J, Yu YS, Lim Y, Lee S, Lee J, Song H, Park S.   +7 more
europepmc   +1 more source

Structural characterization and optimum machining parameters of jute/carbon fibre hybrid reinforced epoxy composite laminates

Polymer International, Volume 75, Issue 9, Page 804-817, September 2026.
Hybrid jute/carbon epoxy laminates have better mechanical performance and less drilling damage by the use of optimized stacking sequence and machining parameters. Abstract Three composite laminate systems were produced using the standard hand lay‐up method: jute‐fibre‐reinforced polymer (JFRP), carbon‐fibre‐reinforced polymer (CFRP) and a hybrid of the
Paulraj Prabhu, Anbalagan Arunkumar, Nadir Ayrilmis, Vellingiri Suresh, Ram Subbiah, Emarose Shankar   +5 more
wiley   +1 more source