Results 81 to 90 of about 10,476 (314)
Advances in Magnesium‐Based Thermoelectrics: A Critical Review
Advanced Materials, EarlyView.Magnesium‐based thermoelectric materials have emerged as promising candidates for low‐to‐mid‐temperature energy conversion due to their abundance, low cost, and competitive performance. This review summarizes recent advances in Mg3X2, MgAgSb, and Mg2X systems, covering transport mechanisms, fabrication strategies, stability challenges, and device ...
Li‐Min Zhang +5 more
wiley +1 more source
EFFECT OF RESISTANCE SPOT WELDING PARAMETERS FOR STEEL SHEETS ON THE WELDING STRENGTH
Diyala Journal of Engineering Sciences, 2015 The resistance spot welding processes are widely used in the automobile, appliance and industries that use steel sheets, because of its low cost, high productivity, simple mechanism and applicability for automation.
Khalid Ahmed Al-Dolaimy
doaj
Laser beam oscillation welding for automotive applications
, 2022 S.1039-1047Laser beam oscillation, applied one- or two-dimensional to the actual welding process, influences the welding process in terms of compensation of tolerances and reduction of process emissions like spatter and melt ejections that occur in ...
Müller, A., Goecke, S.F., Rethmeier, M.
core +1 more source
Advanced Materials, EarlyView.Ultrathin lithium metal anodes (≤15 µm) offer a promising route to high‐energy‐density batteries due to their high capacity and low potential. This review presents design principles for ultrathin Li, evaluates fabrication strategies, and discusses challenges in liquid and solid‐state cells.
Cheng Wang +9 more
wiley +1 more source
Resistance Spot Welding of dissimilar Steels
Acta Polytechnica, 2012 This paper presents an analysis of the properties of resistance spot welds between low carbon steel and austenitic CrNi stainless steel. The thickness of the welded dissimilar materials was 2 mm.
Ladislav Kolařík +5 more
doaj
Investigation of thermal techniques to mitigate buckling distortion in welding panels [PDF]
, 2012 This thesis describes the advancements of the application of thermal tensioning techniques to different weld geometries in order to eliminate buckling distortion.
Nagy, T.
core
Advanced Materials Technologies, EarlyView.ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel +4 more
wiley +1 more source
A Soft Robotic Device for Targeted Massage Therapy of Residual Limbs
Advanced Robotics Research, EarlyView.Residual limb edema after amputation can hinder recovery and delay prosthetic fitting. This study presents a soft‐robotic wearable device that delivers sequential compression through pneumatic McKibben actuators. By replicating the principles of manual lymphatic drainage, the device generates controlled mechanotherapeutic pressure patterns, providing a
Maria Grazia Polizzotto +5 more
wiley +1 more source
Resistance Spot Welding of Aluminum Alloy and Carbon Steel with Spooling Process Tapes
Metals, 2019 Many lightweight materials, including aluminum alloy, magnesium alloy, and plastic, have been used for automotives. Aluminum alloy—the most commonly utilized lightweight metal—has poor resistance spot weldability owing to its inherent ...
Seungmin Shin +3 more
doaj +1 more source
Durability of Soft Pneumatic Actuators: A Review and Benchmarking Protocol
Advanced Robotics Research, EarlyView.Lack of durability is a key challenge hindering the broad scale adoption of soft pneumatic actuators (SPAs) in automation industries. This review provides a comprehensive overview of existing research on SPA durability, introduces a standardized durability benchmarking protocol to consolidate the testing of SPAs, and outlines promising directions for ...
Dickson Chiu Yu Wong +2 more
wiley +1 more source