Results 31 to 40 of about 836,375 (282)

Influence of diesel surrogates on the behavior of simplified spray models [PDF]

, 2012
Numerous experimental investigations make use of diesel surrogates to make the computational time reasonable. In the few studies where measured (surrogate and real diesel) and computed (surrogate only) results have been compared, the selection ...
F Battin-Leclerc, H Wanga, JM Desantes, JV Pastor, N Peters, R Payri, RH Natelson   +6 more
core   +2 more sources

Efeito da adição de látex nas pastas de cimento branco no estado endurecido

Ambiente Construído
Este trabalho investiga o impacto da utilização de látex poliméricos em propriedades de pastas de cimento Portland branco no estado endurecido. Para tanto, foram utilizados dois látex com propriedades físico-químicas distintas: EVA (etileno de vinil ...
Carlos Eduardo Carbone, Hudson Santos, Roberto Cesar de Oliveira Romano, Rafael Giuliano Pileggi   +3 more
doaj   +1 more source

Investigation of crystallinity, mechanical properties, fracture toughness and cell proliferation in plasma sprayed graphene nano platelets reinforced hydroxyapatite coating

Materials Research Express, 2020
Graphene nanoplatelets (GNPs) (0, 1 wt% and 2 wt%) reinforced hydroxyapatite (HA), denoted by HA, HA-1G and HA-2G respectively, coatings were fabricated on titanium substrate (Ti-6Al-4V) through atmospheric plasma spraying.
Swarnima Singh, Krishna Kant Pandey, O S Asiq Rahman, Swati Haldar, Debrupa Lahiri, Anup Kumar Keshri   +5 more
doaj   +1 more source

Challenges in charge preparation and combustion in homogeneous charge compression ignition engines with biodiesel: A review

Energy Reports, 2019
Homogeneous charge compression ignition (HCCI) engines have high efficiency and lower NOx-soot emissions than diesel and gasoline engines. However, these engines suffer from high HC, CO and unregulated emissions and combustion phasing control.
V.D. Chaudhari, D. Deshmukh
doaj   +1 more source

Design and Test of a Jet Remote Control Spraying Machine for Orchards

AgriEngineering, 2021
Aimed at issues associated with the poor air supply and poor automatic targeting accuracy of existing orchard sprayers, this paper designs a jet-type orchard remote control sprayer with automatic targeting which is suitable for standardized orchards in ...
Chi Ma, Guanglin Li, Qiangji Peng
doaj   +1 more source

Effects of injection pressure and impingement distance on flat-wall impinging spray flame and its heat flux under diesel engine-like condition

Advances in Mechanical Engineering, 2019
Heat loss is one of the main causes of energy losses in modern direct injection diesel engines. This heat loss of the engine occurs during combustion, mainly due to the heat transfer between the impinging spray flame and the piston cavity wall.
Rizal Mahmud, Toru Kurisu, Keiya Nishida, Yoichi Ogata, Jun Kanzaki, Onur Akgol   +5 more
doaj   +1 more source

Spray forming

Progress in Materials Science, 1995
Spray forming is a relatively new manufacturing process for near net shape preforms in a wide variety of alloys. Spray formed materials have a characteristic equiaxed microstructure with small grain sizes, low levels of solute partitioning, and inhibited coarsening of secondary phases.
openaire   +1 more source

Planning Family Spending [PDF]

, 1958
PDF pages ...
Spray, Mabel
core  

Hyperosmotic stress induces PARP1‐mediated HPF1‐dependent mono(ADP‐ribosyl)ation

FEBS Letters, EarlyView.
Sorbitol‐induced hyperosmotic stress rapidly induces reversible mono(ADP‐ribosyl)ation (MARylation) on PARP1 without the signs of genotoxic signaling. We show that PARP1 autoMARylation is HPF1 dependent and forms hydroxylamine‐resistant O‐glycosidic linkages.
Anna Georgina Kopasz, Mihály Mérey, Rebeka Vásárhelyi, Ramóna Pék, Victor Imburchia, László Henn, Adrián Kószó, Nicholas D. Lakin, Ivan Ahel, Sébastien Huet, Ágnes Czibula, Gyula Timinszky   +11 more
wiley   +1 more source

A Comparative Study of the Life Cycle Inventory of Thermally Sprayed WC-12Co Coatings

Metals
In this research, a life cycle inventory (LCI) is developed for tungsten carbide–cobalt (WC-Co) coatings deposited via atmospheric plasma spray (APS), high-velocity oxy-fuel (HVOF), and cold gas spray (CGS) techniques.
Edwin Rúa Ramirez, Alessio Silvello, Edwin Torres Diaz, Rodolpho Fernando Vaz, Irene Garcia Cano   +4 more
doaj   +1 more source