Results 71 to 80 of about 845,620 (310)
Influence of excipients on spray-dried powders for inhalation [PDF]
, 2014 Two areas attracting considerable attention when developing effective pulmonary drug delivery systems include the improvement of aerosolisation efficiency of the inhaled formulation and the controlled release of drug from the formulation following ...
Adi +45 more
core +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Total spray tray (TST) for distillation columns: A new generation tray with lower pressure drop [PDF]
Chemical Industry and Chemical Engineering Quarterly, 2017 As a critical gas-liquid contact component, trays play an important role in the performance of distillation column. In this paper, the hydrodynamics of a new type of tray, the total spray tray (TST), were investigated.
Ran Wang +4 more
doaj +1 more source
Fuel distribution measurements in a model low NOx double annular combustor using laser induced fluorescence [PDF]
, 2010 Planar laser induced fluorescence (PLIF) was employed in a three sector, low NOx double annular combustor in order to characterise the combusting fuel spray.
Greenhalgh, D. A., Lockett, R. D.
core
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Cavitation Inside Enlarged And Real-Size Fully Transparent Injector Nozzles And Its Effect On Near Nozzle Spray Formation [PDF]
, 2011 The effect of string cavitation in various transparent Diesel injector nozzles on near nozzle spray dispersion angle is examined. Additional PDA measurements on spray characteristics produced from real-size transparent nozzle tips are presented ...
Arcoumanis, C. +3 more
core
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
Synthesis of nanosized metal particles from an aerosol
Vojnotehnički Glasnik, 2013 The synthesis of metallic nanoparticles from the precursor solution of salts using the ultrasonic spray pyrolysis method was considered in this work. During the control of process parameters (surface tension and density, the concentration of solution ...
Srećko R. Stopić
doaj +1 more source