Results 81 to 90 of about 14,421 (309)

Methodology for the Regulation of Boom Sprayers Operating in Circular Trajectories

Sensors, 2011
A methodology for the regulation of boom sprayers working in circular trajectories has been developed. In this type of trajectory, the areas of the plots of land treated by the outer nozzles of the boom are treated at reduced rates, and those treated by ...
Alfredo Serreta, Francisco Javier Garcia-Ramos, Mariano Vidal, Antonio Boné   +3 more
doaj   +1 more source

Revealing the γ′ and γ″ Phase Fractions of Additively Manufactured and Differently Heat‐Treated Nickel‐Base Superalloy IN718 by Atom Probe Tomography and Their Impact on Mechanical Properties

Advanced Engineering Materials, EarlyView.
Additive manufacturing is a promising route for the production of Ni‐base superalloys for turbine applications, such as Inconel 718. Nonetheless, it induces various changes in the microstructure and performance of these materials. One such change is the incidence of the δ‐Ni3Nb phase, whose impact on microstructure, aging precipitate fractions, and ...
Guilherme Maziero Volpato, Jan Vollhüter, Benedikt Diepold, Martin Sebastian Meier, Martin Pröbstle, Mathias Göken, Thomas Niendorf, Peter Felfer, Steffen Neumeier   +8 more
wiley   +1 more source

Analysis of the Air Flow Generated by an Air-Assisted Sprayer Equipped with Two Axial Fans Using a 3D Sonic Anemometer

Sensors, 2012
The flow of air generated by a new design of air assisted sprayer equipped with two axial fans of reversed rotation was analyzed. For this goal, a 3D sonic anemometer has been used (accuracy: 1.5%; measurement range: 0 to 45 m/s).
Javier Aguirre, Hugo Malón, Mariano Vidal, Antonio Boné, F. Javier García-Ramos   +4 more
doaj   +1 more source

Development of a Novel Processing Route for Dispersoid/Precipitation‐Strengthened High Conductive Copper Alloys by Using Metalized Nanoceramics in Additive Manufacturing

Advanced Engineering Materials, EarlyView.
This study explores a process chain to produce dispersoid‐strengthened CuCr1Zr for applications requiring high strength and conductivity. Using gas‐atomized powder and copper‐plated alumina nanoparticles, additive manufacturing is performed via powder bed based additive manufacturing with green and red lasers, followed by heat treatment.
Heinrich von Lintel, Abdelrahman Elsayed, Lukas Mielewczyk, Katja Eichmann, Julia Grothe, Ulrich Krupp, Avinash Hariharan, Katrin Jahns   +7 more
wiley   +1 more source

Aferição da exatidão dos saquinhos plásticos, empregados na determinação da vazão de pulverizadores Accuracy of graded polythene bags used for calibration of agricultural sprayers

Planta Daninha, 1984
A utilização de sacos plásticos graduados para a medida da vazão de pulverizadores está ba stante di fundida entre técnicos e agricultores. 0 seu emprego é simples, consistindo, basicamente, em se coletar o líquido pulverizado por um bico durante o ...
T. Matuo
doaj   +1 more source

Analysis of Temperature and Stress Distribution on the Bond Properties of Hybrid Tailored Formed Components

Advanced Engineering Materials, EarlyView.
Hybrid materials enable high‐performance components but are challenging to process. This study explores an inductive heating concept with spray cooling for steel–aluminum specimens in a two‐step process including friction welding and cup backward extrusion.
Armin Piwek, Eduard Ortlieb, Caner‐Veli Ince, Julius Peddinghaus, Hendrik Wester, Johanna Uhe, Annika Raatz, Kai Brunotte   +7 more
wiley   +1 more source

Eficiência de diferentes ramais de pulverização e volumes de calda no controle de Brevipalpus phoenicis na cultura do café Efficiency of different spraying lances and spraying volumes on the control of Brevipalpus phoenicis in coffee crops

Revista Brasileira de Entomologia, 2010
O ácaro Brevipalpus phoenicis é encontrado nos cafezais do Brasil desde a década de 50. Responsável por perdas indiretas por ser o vetor de uma doença virótica requer constantes medidas de controle, sendo a mais utilizada baseada na pulverização de ...
Ana Paula Fernandes, Marcelo da Costa Ferreira, Carlos Amadeu Leite de Oliveira   +2 more
doaj   +1 more source

Advances in Hybrid Icing and Frosting Protection Strategies for Optics, Lens, and Photonics in Cold Environments Using Thin‐Film Acoustic Waves

Advanced Engineering Materials, EarlyView.
This article provides a comprehensive overview of fundamentals and recent advances of transparent thin‐film surface acoustic wave technologies on glass substrates for monitoring and prevention/elimination of fog, ice, and frost. Fogging, icing, or frosting on optical lenses, optics/photonics, windshields, vehicle/airplane windows, and solar panel ...
Hui Ling Ong, Zhangbin Ji, Luke Haworth, Yihao Guo, Jaime del Moral, Stefan Jacob, Ana Borras, Agustin R. Gonzalez‐Elipe, Jikai Zhang, Jian Zhou, Glen McHale, Yong‐Qing Fu   +11 more
wiley   +1 more source

Powder Metallurgy and Additive Manufacturing of High‐Nitrogen Alloyed FeCr(Si)N Stainless Steel

Advanced Engineering Materials, EarlyView.
The alloying element Nitrogen enhances stainless steel strength, corrosion resistance, and stabilizes austenite. This study develops austenitic FeCr(Si)N steel production via powder metallurgy. Fe20Cr and Si3N4 are hot isostatically pressed, creating an austenitic microstructure.
Louis Becker, Felix Radtke, Jonathan Lentz, Santiago Benito, Christoph Broeckmann, Sebastian Weber   +5 more
wiley   +1 more source

Aerial, ground and chemigation spray deposition on corn for the control of spodoptera frugiperda (lepidoptera: noctuidae) Deposição de calda por aplicação aérea, terrestre e via água de irrigação na cultura do milho para o controle de Spodoptera frugiperda (Lepidoptera: Noctuidae)

Ciência e Agrotecnologia, 2013
Pesticides can be applied by aircraft, ground-sprayers or sprinkler irrigation. However, selecting the best option is complicated by the limited number of studies comparing these techniques.
João Paulo Arantes Rodrigues da Cunha, Ana Paula de Castro Nascimento   +1 more
doaj