Results 1 to 10 of about 5,555 (167)
Summaries of Doctor and Master Theses Master of Engineering, 1965 Mechanical ...
openaire +1 more source
Effect of Microstructure on the Instantaneous Springback and Time-dependent Springback of DP600 Dual Phase Steel [PDF]
Rongting Li +4 more
openaire +1 more source
Springback: Influence of an Accurate Trimming on Springback
Avetisyan, Marianna +2 more
openaire +1 more source
Influence of Bend Holding on Springback and Time-Dependent Springback in Sheet Metal Bending
Matsugi, Kouki, Hino, Ryutaro
openaire +1 more source
Some of the next articles are maybe not open access.
International Journal of Mechanical Sciences, 2002
Springback, the elastically-driven change of shape of a part after forming, has been measured under carefully-controlled laboratory conditions corresponding to those found in press-forming operations. Constitutive equations emphasizing low-strain behavior were generated for three automotive body alloys: drawing-quality silicon-killed steel; high ...
R H Wagoner, D K Matlock
exaly +2 more sources
Springback, the elastically-driven change of shape of a part after forming, has been measured under carefully-controlled laboratory conditions corresponding to those found in press-forming operations. Constitutive equations emphasizing low-strain behavior were generated for three automotive body alloys: drawing-quality silicon-killed steel; high ...
R H Wagoner, D K Matlock
exaly +2 more sources
International Journal of Plasticity, 2013
Abstract For purposes of this review, springback is the elastically driven change of shape of a metal sheet during unloading and following forming. Scientific advances related to this topic have accelerated dramatically over roughly the last decade, since the publication of two reviews in the 2004–2006 timeframe ( Wagoner, 2004 , Wagoner et al ...
Robert H. Wagoner +2 more
exaly +3 more sources
Abstract For purposes of this review, springback is the elastically driven change of shape of a metal sheet during unloading and following forming. Scientific advances related to this topic have accelerated dramatically over roughly the last decade, since the publication of two reviews in the 2004–2006 timeframe ( Wagoner, 2004 , Wagoner et al ...
Robert H. Wagoner +2 more
exaly +3 more sources
Springback Determination By Springback Index Approach
SAE Technical Paper Series, 2005<div class="htmlview paragraph">A new mechanical parameter, Springback Index (SBI), is proposed to reflect the magnitude of sheet-metal springback at a given flow stress level. Through conducting Tension-Unloading-Reloading (TUR) tests and measuring the Effective Unloading Modulus (EUM) Parameter, which is defined as the ratio of the non-linear ...
Shuwen Sun, Hongwei Ma, Zhirui Wang
openaire +1 more source
International Journal of Mechanical Sciences, 2002
Springback, the elastically-driven change of shape of a part after forming, has been simulated with 2-D and 3-D finite element modeling. Simulations using solid and shell elements have been compared with draw-bend measurements presented in a companion paper.
Li, K. P., Carden, W. P., Wagoner, R. H.
openaire +2 more sources
Springback, the elastically-driven change of shape of a part after forming, has been simulated with 2-D and 3-D finite element modeling. Simulations using solid and shell elements have been compared with draw-bend measurements presented in a companion paper.
Li, K. P., Carden, W. P., Wagoner, R. H.
openaire +2 more sources
2023
When producing a part, either by deep drawing, stretch forming or bending, flat sheet is transformed into a design shape and dimension. At the end of the forming process, when the part has been released from the forces of the forming tool, there is a distortion in the shape and dimension of the formed oart. This distortion is termed springback.
Grizelj, Branko +3 more
openaire +2 more sources
When producing a part, either by deep drawing, stretch forming or bending, flat sheet is transformed into a design shape and dimension. At the end of the forming process, when the part has been released from the forces of the forming tool, there is a distortion in the shape and dimension of the formed oart. This distortion is termed springback.
Grizelj, Branko +3 more
openaire +2 more sources

