Results 11 to 20 of about 5,555 (167)

Numerical Investigation of Springback in Mechanical Clinching Process

open access: yesInternational Journal of Engineering Materials and Manufacture, 2017
In this work, a numerical investigation was conducted to study the springback phenomena in the mechanical clinching process. The springback values were calculated using finite element simulations and it was found that these values depend strongly on the ...
Mohanna Eshtayeh   +2 more
doaj   +5 more sources

Influence of the forming process on springback [PDF]

open access: yesIOP Conference Series: Materials Science and Engineering, 2022
Abstract The use of advanced high-strength steels (AHSS) is associated with increased springback and represents a great challenge for today’s press shops with regard to the dimensional accuracy of cold-formed sheet metal parts. Springback, its appearance and characteristics are mainly dependent on the stress state introduced by the ...
Durmaz, U.   +4 more
openaire   +2 more sources

An Alternate Method to Springback Compensation for Sheet Metal Forming [PDF]

open access: yesThe Scientific World Journal, 2014
The aim of this work is to improve the accuracy of cold stamping product by accommodating springback. This is a numerical approach to improve the accuracy of springback analysis and die compensation process combining the displacement adjustment (DA ...
Waluyo Adi Siswanto   +3 more
doaj   +2 more sources

Springback Calibration of a U-Shaped Electromagnetic Impulse Forming Process

open access: yesMetals, 2019
A three-dimensional (3D) finite-element model (FEM), including quasi-static stamping, sequential coupling for electromagnetic forming (EMF) and springback, was established to analyze the springback calibration by electromagnetic force.
Xiaohui Cui   +4 more
doaj   +2 more sources

Springback prediction of sheet metal hydroforming using finite element analysis and artificial neural networks [PDF]

open access: yesInternational Journal of Applied Mechanics and Engineering
The objective of this paper is to develop a method for the rapid estimating springback in the hydroforming process of circular sheets. First, the springback behavior has been studied with using finite element simulations for various configurations such ...
YASSINE FARTOUH   +2 more
doaj   +2 more sources

Towards an accurate springback prediction : experiments and modeling [PDF]

open access: yes, 2018
Finite element (FE) simulations are used extensively during the tool design stage to predict the springback; it can then be compensated for by adapting the tool’s geometry. The tool is adapted in such a way that the formed product takes the intended shape after springback.
Torkabadi, Ali, Ali Torkabadi
openaire   +3 more sources

Springback Modeling in L-bending Process Using Continuum Damage Mechanics Concept

open access: yesJournal of Applied and Computational Mechanics, 2015
Springback is one of the most common and important issues in metal forming area. Due to it depends on variety of parameters, it is hard to predict. Hence, in this paper, the effect of continuum damage mechanics (CDM) based on the Lemaitre isotropic ...
Mehdi Shahabi, Ali Nayebi
doaj   +2 more sources

Simulation and experimental study on springback deformation of duplex stainless steel heat exchanger sheet

open access: yesJournal of Hebei University of Science and Technology, 2021
The significant springback deformation of metal sheet makes the development of plate and frame heat exchanger extremely difficult for duplex stainless steel.In this paper,a coupled explicit to implicit finite element methods was adopted to predict ...
Guan LI, Guofeng GENG, Hailan HE
doaj   +1 more source

Prediction of springback in local bending of hull plates using an optimized backpropagation neural network [PDF]

open access: yesMechanical Sciences, 2021
Springback is an inevitable problem in the local bending process of hull plates, which leads to low processing efficiency and affects the assembly accuracy.
B. Xu, L. Li, Z. Wang, H. Zhou, D. Liu
doaj   +1 more source

Computer aided sheet metal forming process design [PDF]

open access: yesComputer Methods in Materials Science, 2006
“A system for the computer aided design of sheet metal forming is described. This system was combined with the FEM and theoretical method of determination of a forming limit stress diagram (FLSD).
Zbigniew Zimniak
doaj   +1 more source

Home - About - Disclaimer - Privacy