Results 61 to 70 of about 194,524 (260)

Enhancing Bubble Removal in Geometry‐Optimized Electrodes

Advanced Engineering Materials, EarlyView.
3D‐printed lattice electrodes outperform stochastic foams in alkaline water electrolysis despite 20%–25% lower surface area. Straight flow channels generate Venturi‐like bubble entrainment, suppressing gas accumulation that renders foam interiors electrochemically inactive.
Florian Wiesner, Peter Förster, Alexander Limper, Anselm Brodersen, Matthias Wessling, John Linkhorst   +5 more
wiley   +1 more source

Microstructure evolution and corrosion behavior of laser metal deposited 316L stainless steel bipolar plates subjected to tensile deformation

Journal of Materials Research and Technology
The impact of tensile deformation on the microstructural characteristics and corrosion resistance of 316L austenitic stainless steel (ASS) produced via laser metal deposition (LMD) was systematically studied using electron backscatter diffraction (EBSD ...
Pei Li, Shaohua Zhang, Baosheng Liu, Yinghui Wei, Lifeng Hou, Pengpeng Wu, Xiaoxia Ren, Yuezhong Zhang, Huihu Lu   +8 more
doaj   +1 more source

Designing Polymer Nanocomposites for X‐Ray Shielding: Mechanisms, Architectures, and Scalable Processing

Advanced Engineering Materials, EarlyView.
This review highlights advances in lightweight, lead‐free polymer nanocomposites for diagnostic X‐ray shielding. By linking filler chemistry, dispersion, architecture, and photon interaction mechanisms, it establishes structure–performance relationships guiding material design.
Aklilu G. Messele, Hossein Ipakchi, Tizazu H. Mekonnen   +2 more
wiley   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Steels and Stainless Steels

24 pages, contribution to the CAS - CERN Accelerator School: Mechanical & Materials Engineering for Particle Accelerators and Detectors, 2-15 June 2024, Sint-Michielsgestel ...
openaire   +2 more sources

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Horizontal rotating arc narrow-gap GTAW of thick Ti–6Al–4V alloy

Journal of Materials Research and Technology
The horizontal welding method helps simplify assembly and construction for large cylindrical components. Nonetheless, a notable challenge arises during horizontal welding, as the molten pool tends to flow downward due to gravity. To overcome this problem,
Kan Li, Chuanbao Jia, Peidun Chen, Jiakun Hu, Zhuo Wei, Qingye Zheng, Yinggang Wang, Chuansong Wu   +7 more
doaj   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source