Results 181 to 190 of about 1,096 (216)
Some of the next articles are maybe not open access.
Thermal Engineering (English Translation of Teploenergetika), 2006
Results of calculation studying of a possibility of topping of a steam-turbine unit (STU) with a type T-110/120-12.8 turbine of the Urals Turbine Works (UTZ) by a gas-turbine unit (GTU) of 25-MW capacity the waste-gases heat of which is used to substitute for high-pressure bleedoffs of STU is considered.
A D Trukhnii
exaly +2 more sources
Results of calculation studying of a possibility of topping of a steam-turbine unit (STU) with a type T-110/120-12.8 turbine of the Urals Turbine Works (UTZ) by a gas-turbine unit (GTU) of 25-MW capacity the waste-gases heat of which is used to substitute for high-pressure bleedoffs of STU is considered.
A D Trukhnii
exaly +2 more sources
2023 4th International Conference on High Voltage Engineering and Power Systems (ICHVEPS), 2023
Kevin Marojahan Banjar-Nahor +1 more
exaly +2 more sources
Kevin Marojahan Banjar-Nahor +1 more
exaly +2 more sources
Installation of molten-metal seals in steam-turbine valves
Power Technology and Engineering, 2007Gaps in valves between the stems and boxes are a source of rather large steam and heat losses in power-generating steam turbines. A unique development of specialists employed by the Vserossiiskii Teplotekhnicheskii Institut — superairtight seals (SAS) with composite materials, which permit reliable sealing of valves with minimal friction within the ...
A. S. Sozaev +3 more
openaire +1 more source
2021 3rd International Youth Conference on Radio Electronics, Electrical and Power Engineering (REEPE), 2021
The article presents the results of the analysis of modern requirements of operational control, monitoring and approaches to the implementation of diagnostics of the technical condition of steam turbine installations of thermal power plants. The experience of implementing monitoring and diagnostics systems at domestic thermal power plants with steam ...
M.M. Sultanov +3 more
openaire +1 more source
The article presents the results of the analysis of modern requirements of operational control, monitoring and approaches to the implementation of diagnostics of the technical condition of steam turbine installations of thermal power plants. The experience of implementing monitoring and diagnostics systems at domestic thermal power plants with steam ...
M.M. Sultanov +3 more
openaire +1 more source
Cogeneration steam turbines for combined-cycle installations of 170–230 MW
Thermal Engineering, 2008Design specifics, principal thermal schemes, and efficiency of cogeneration steam turbines operating as part of combined-cycle installations are considered. These turbines are developed on the basis of serially manufactured steam turbines of ZAO Ural Turbine Works.
G. D. Barinberg +3 more
openaire +1 more source
ASME 2022 Power Conference, 2022
Abstract There is limited literature available when it comes to fault finding of oil operated control valves associated with power plants. This limitation is further aggravated due to lack of Original Equipment Manufacturer (OEM) support in remote settings.
Fahad Qureshi +2 more
openaire +1 more source
Abstract There is limited literature available when it comes to fault finding of oil operated control valves associated with power plants. This limitation is further aggravated due to lack of Original Equipment Manufacturer (OEM) support in remote settings.
Fahad Qureshi +2 more
openaire +1 more source
Increasing reliability of system water heaters for steam–turbine installations at the design stage
Thermal Engineering, 2015A system for designing water heaters of steam–turbine installations based on uniting standards, reference information, and some numerical procedures with design procedures via wide use of parameterization is considered. The developed design system is based on extensive application of modern information technologies.
V. I. Brezgin +2 more
openaire +1 more source
Lubricating Marine Steam Turbine Installations
Industrial Lubrication and Tribology, 1969IN a paper to the Institute of Marine Engineers recently, J. F. Preston, C.Eng., M.I.Mech.E., M.I.Mar.E., Head of Engineering—Ship Design, Shell International Marine Ltd., gave his experiences of past and presently operating steam turbines with a view to providing valuable guide lines for future designs.
openaire +1 more source
Volume 9: Oil and Gas Applications; Organic Rankine Cycle Power Systems; Steam Turbine, 2020
Abstract During installation process, most of 1000MW-class nuclear power steam turbines will undergo certain deformations due to their own big size and heavy weight, which will change seal clearances in the steam passage. The clearance change will affect steam turbine’s efficiency, and may cause rubbing faults and even strong abnormal ...
Daohui Ji +5 more
openaire +1 more source
Abstract During installation process, most of 1000MW-class nuclear power steam turbines will undergo certain deformations due to their own big size and heavy weight, which will change seal clearances in the steam passage. The clearance change will affect steam turbine’s efficiency, and may cause rubbing faults and even strong abnormal ...
Daohui Ji +5 more
openaire +1 more source