Results 191 to 200 of about 1,096 (216)

Comparison and Ranking of Steam-Turbine Installations of Thermal Power-Stations’ Power-Generating Units by Working Efficiency

Thermal Engineering, 2018
Increasing the objectivity of comparison and ranking of working efficiency of steam-turbine installations of thermal power-stations' power-generating units under conditions when the accuracy of technical and economic indices (TEI) to be calculated by energy characteristics leaves much to be desired; in other words, the results of TEI analysis are far ...
E. M. Farhadzadeh, A. Z. Muradaliyev, Y. Z. Farzaliyev, S. A. Abdullayeva   +3 more
openaire   +1 more source

Discussion and Realization on Quality Control Methods of Power Steam Turbine-Generator Unit Installation

Advanced Materials Research, 2014
Based on the practical experience of turbine unit installation, combined with the project quality management theory, analyzed the impact factors of turbine installation quality, explored the quality control content, and formed a more perfect of quality control methods system ultimately.
openaire   +1 more source

Discussion and Realization on Quality Management Methods of Steam Turbine Unit Installation in Tianjin SDIC Jinneng Power Plant

Advanced Materials Research, 2012
During the steam turbine unit installation, combined with the project quality management theory, summarized the quality management methods of making the quality plan and the guarantee, quality control and improvement. Achieve the good results through the application in the SDIC Power Plant team turbine unit installation.
Dong You Jia, Qing Nian Zhang, Zhong Chuan Liu   +2 more
openaire   +1 more source

Installations for producing electrospark erosion- and abrasion-resistant coatings on the blades of steam turbines of thermal and nuclear power plants

Surface Engineering and Applied Electrochemistry, 2017
This article is devoted to the creation of installations for generating electric spark erosion- and abrasion-resistant protective and strengthening coatings on the blades of steam turbines of thermal and nuclear power plants such as GBF and KGB, developed and manufactured by the OAO VTI.
A. V. Belyakov, A. N. Gorbachev, V. V. Mikhailov, B. F. Reutov, A. A. Fokin   +4 more
openaire   +1 more source

Increase of Efficiency of a Heat Supply Steam Turbine by Integrating RES: A Study Analysis of T-100/120-130-3 Steam Turbine installed in TE-TO Zagreb District Heating Plant

2020
According to recent estimates by the World Meteorological Organization, temperatures will rise by 3 to 5 degrees Celsius by the end of the century, well above 1.5 degrees, a goal set by the UN Intergovernmental Panel on Climate Change (IPCC). In this regard, solutions should be considered and offered to reduce global warming and CO2 emissions ...
Jukić, Perica, Guzović, Zvonimir
openaire   +1 more source

Numerical Calculation of Seal Clearance Change in Installation Process of a 1000MW Nuclear Steam Turbine HIP Casing

2021
Yanan Yue
exaly  

Effect of NaCl presence caused by salting out on the heterogeneous-homogeneous coupling non-equilibrium condensation flow in a steam turbine cascade

Energy, 2023
Piotr Wisniewski, Xiang Qin, Sławomir Dykas   +2 more
exaly  

Direct-Contact Heat Exchangers for Large Steam Turbine Installations

Proceeding of Advanced Course in Heat Exchangers: Theory and Practice. ICHMT Symposium., 1981
openaire   +1 more source

Thermodynamic analysis of the performance of a hybrid system consisting of steam turbine, gas turbine and solid oxide fuel cell (SOFC-GT-ST)

Energy Conversion and Management, 2020
Jamasb Pirkandi, Arman Maroufi
exaly  

A new type of a gas–steam turbine cycle with increased efficiency

Applied Thermal Engineering, 2001
N Kolev, K Schäber, D Kolev
exaly