Results 61 to 70 of about 596,686 (360)
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source
Effect of Initial Plate Thickness and Reduction on Cladding Ratio of Hot-Rolled Clad Steel Plate
Teshugang, 2014 Effect of the initial cladding ratio 5.40%-15.53% with 0.45C steel, NM360 abrasion-resistant steel, 310S and 316 stainless steel 5.1-15.2 mm initial cladding plate and Q345 carbon steel 82.7-90.0 mm initial base plate and the total reduction 35%-75% on ...
李龙, 张心金, 祝志超, 李萌蘖
doaj
Investigation on Tempering Process of 45Mn2V/Q345 Clad Steel Plate for Saw Blade
Teshugang, 2020 Tempering of the holding time after different temperature of clad steel plate for saw blade steel has been carried out, the hardness of cladding plate and hase plate and the microstructure evolution are measured and observed.
杨跃辉 +4 more
doaj
Structural Performance of Composite Shear Walls under Compression
Applied Sciences, 2017 In order to research the effect of different layout forms of steel plate on the axial compression behavior of a steel plate-concrete composite shear wall, this paper presents the experimental results and analysis of the axial compression behavior of a ...
Tingyue Hao +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Advances in Materials Science and Engineering, 2020 In order to research the effect of heat treatment on the microstructure and corrosion resistance of stainless/carbon steel bimetal plate, the annealing process at 700°C with different times was carried out for stainless/carbon steel bimetal plate ...
Hao Li +3 more
doaj +1 more source
TINJAUAN STABILITAS JEMBATAN RANGKA BAJA TERBUKA DENGAN GARIS KERJA GAYA BATANG YANG TIDAK SENTRIS (Studi kasus pada model jembatan KJI : Apple Bridge) [PDF]
, 2009 Bridge represent element / part of road, that is a construction as transportation link medium between road which is one with other which blocked by barricade in the form of river, creavasse, bog, strait and others.
MUTTAQIEN, SHOBBAH SABILIL
core
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
The research and development of longitudinal profiled (LP) plate
MATEC Web of Conferences, 2018 In this paper, the advantages of the longitudinal profiled(LP) steel plate is described, and the characteristics of LP plate rolling process is introduced. In contrast to the ordinary steel plate, The change rule of the bite angle and other parameters is
Shiping Lu +4 more
doaj +1 more source
Applied Sciences, 2019 A steel plate shear wall often uses partially encased composite (PEC) columns instead of edge frame columns. Such a steel plate shear wall not only bears the gravity load of the structure and resists the bending moment caused by lateral force by taking ...
Zhanzhong Yin, Hui Zhang, Wenwei Yang
doaj +1 more source