Results 51 to 60 of about 596,686 (360)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Ship Hull Steel Plate Deformation Modeling Based on Gaussian Process Regression

Journal of Marine Science and Engineering
The linear heating and formation of steel plates is one of the most critical technologies in shipbuilding. Excellent technology not only provides good hydrodynamics for the hull but also affects the whole hull construction cycle and cost.
Zhiliang Zhang, Ryojun Ikeura, Soichiro Hayakawa, Zheng Wang   +3 more
doaj   +1 more source

Impact Fatigue Characteristics of Valve Leaves for Small Hermetic Reciprocating Compressors [PDF]

, 2010
This paper presents an investigation on the impact fatigue characteristics of valve leaves that are prevalently used in hermetic reciprocating compressors especially for the household type refrigerators.
Altunlu, A. Can, Kara, Serkan, Lazoglu, Ismail, Oguz, Emre   +3 more
core   +3 more sources

Enhancement of EMAT’s efficiency by using silicon steel laminations back-plate [PDF]

, 2018
Silicon steel laminations are introduced as the back-plate to an electromagnetic acoustic transducer (EMAT) to increase the efficiency of the EMAT by increasing the magnitude of the EMAT coil's dynamic magnetic field and the eddy current in the sample ...
Dixon, Steve M., He, Jianpeng, Ren, Weiping, Xu, Ke   +3 more
core   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Analysis of Prefabricated Steel Plate Shear Wall Based on Seismic Performance

Advances in Civil Engineering
Prefabricated steel plate shear walls have garnered significant attention due to their short construction period, low cost, and excellent seismic performance. This study experimentally and numerically compares the plastic development and failure modes of
Xinxing Xu, Qiang Sun, Shuangyi Liang, Yi Li   +3 more
doaj   +1 more source

Plate actuator vibration modes for levitation [PDF]

, 2015
The design of an aluminium or steel plate of various thicknesses for achieving levitation of a small aluminum disk is investigated by simulation using ANSYS.
Almurshedi, A, Atherton, M, Mares, C, Stolarski, T, Wang, Y, Wei, B   +5 more
core  

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Experimental research on the effect of induction reheating on the microstructure and mechanical properties of hot-rolled low-alloy steel plate [PDF]

Materials Research, 2014
Electric induction reheating is used to control the temperature of hot-rolled steel products. To investigate the effect of this on microstructure and mechanical properties, hot-rolled low-alloy steel plate was cooled, reheated, and then either quenched ...
Zejun Chen, Jing Zhang, Liang Yu, Guangjie Huang   +3 more
doaj   +1 more source

Residual stress measurement round robin on an electron beam welded joint between austenitic stainless steel 316L(N) and ferritic steel P91 [PDF]

, 2017
This paper is a research output of DMW-Creep project which is part of a national UK programme through the RCUK Energy programme and India's Department of Atomic Energy.
A.K. Bhaduri, A.N. Forsey, ASTM, Bouchard, C.E. Truman, Chetal, D.J. Smith, Dai, EDF, Evans, F. Hosseinzadeh, Fitzpatrick, Fitzpatrick, H.C. Dey, Holden, Hosseinzadeh, Hosseinzadeh, ISO, ISO/TS 21432, J.A. Francis, Javadi, Javadi, Javadi, Javadi, Javadi, K. Abburi Venkata, Kartal, Kerr, Leggatt, M.C. Smith, Mahmoudi, Moat, N. Naveed, Naveed, Noyan, Olabi, Olabi, P.J. Bouchard, Pagliaro, Pagliaro, Prime, Prime, R.A. Ainsworth, Rossini, S. Gungor, S. Mahadevan, Schajer, Shan, Traore, Traore, Vasileiou, Vasileiou, Venkata, Venkata, VEQTER, Withers, Y. Javadi, Yaghi, Zhang   +57 more
core   +3 more sources