Results 21 to 30 of about 2,844 (216)
A basis for the analysis of surface geometry of spiral bevel gears [PDF]
, 1983 Geometrical procedures helpful in the fundamental studies of the surface geometry of spiral bevel gears are summarized. These procedures are based upon: (1) fundamental gear geometry and kinematics as exposited by Buckingham, et al; (2) formulas ...
Coy, J. J., Huston, R. L.
core +1 more source
Parametric Design of Straight Bevel Gears Based on Solidworks [PDF]
Proceedings of the 2nd International Conference on Computer Application and System Modeling, 2012 The Visual Basic program of standard straight bevel gear's parametric design based on Solidworks software was completed. The geometric features of bevel gears were analyzed, parametric design variables were defined, each control point was determined in Cartesian Coordinate System.
Wei Zhang, Yuxia Shan
openaire +1 more source
A Nanoparticle‐Integrated Complete Manufacturing Pipeline of Chemically Engineered Exosomes
Advanced Science, EarlyView.We report a novel manufacture technology of chemically engineered exosomes. The four steps of manufacturing, i.e., biogenesis, loading, isolation, and storage, are integrated by the use of a nanoparticle. The manufacture technology incorporates three innovative components, i.e., a new nano‐bio effect, a new composite nanoparticle, and a new isolation ...
Xiaowei Wen +13 more
wiley +1 more source
Известия высших учебных заведений: Нефть и газ, 2016 The aim of this thesis is to develop computer program shows generating process of the longitudinal-crowned gear for straight bevel gears with a small shaft angle with non-generated gear and generated pinion.
A. A. Pazyak, V. N. Syzrantsev
doaj +1 more source
Residual Stress and Deformation Analysis in Machining Split Straight Bevel Gears
Strojniški vestnik – Journal of Mechanical Engineering, 2021 In the machining of split straight bevel gears, the stiffness changes and internal stress are redistributed, which leads to serious deformation of the gear blank after machining. To rectify this problem, q finite element model is established by transforming the processing information of the gear blank into the finite element simulation calculation ...
Wang, Bin +6 more
openaire +2 more sources
Limnology and Oceanography: Methods, EarlyView.Abstract Benthic incubation chambers enclose a known volume of water overlying a known area to measure water chemistry changes and are typically used to quantify the metabolic activity of benthic organisms or communities. Here we present an economical benthic incubation chamber for shallow, low‐flow environments, built using off‐the‐shelf components ...
Luke D. Groff +2 more
wiley +1 more source
Small, EarlyView.ABSTRACT The rapid expansion of the Internet of Things (IoT) and wearable electronics necessitates sustainable power sources to replace the limited electrochemical battery. While mechanical energy harvesting offers a promising solution, traditional harvesters face challenges of irregular and low−frequency environmental sources. This review presents the
Yongbin Han +2 more
wiley +1 more source
SELECTED GEARS CUTTING METHODS DEVELOPMENT [PDF]
Scientific Journal of Silesian University of Technology. Series Transport, 2015 The paper presents a somewhat extended approach to the cutting tools classification. After that authors present results of the research concerning the form – grinding of spur gears with helical teeth.
Stanisław PŁONKA +3 more
doaj
Geometric Modeling and Fatigue Strength Simulation of Bevel Gears with Variable Radius Tooth Root
Jixie chuandong, 2022 Aiming at the problem that most of the teeth root of straight bevel gears adopt fixed radius fillet transition with 0.3 times of modulus， which tends to to cause large bending stress on the tooth root and reduce the service life of bevel gears， a design ...
Haohan Zeng +5 more
doaj
Non‐Rigid 3D Shape Correspondences: From Foundations to Open Challenges and Opportunities
Computer Graphics Forum, EarlyView.Abstract Estimating correspondences between deformed shape instances is a long‐standing problem in computer graphics; numerous applications, from texture transfer to statistical modelling, rely on recovering an accurate correspondence map. Many methods have thus been proposed to tackle this challenging problem from varying perspectives, depending on ...
A. Zhuravlev +14 more
wiley +1 more source