Results 1 to 10 of about 7,449 (165)

Characterization of Full Bridge Strain Transducers for Haulage Equipment Payload Distribution Monitoring [PDF]

Sensors
Creating a dependable approach for identifying both the mass of a shuttle car and how material is distributed in it removes the need for equipment operators to manually engage the flight chain.
Jean-Pierre Strydom, Steve Schafrik, Zach Agioutantis, Matt Beck, Joseph Sottile   +4 more
doaj   +2 more sources

Verification of the Gage Factor of a High-Temperature Strain Gage for the Dynamic Testing of Gas Turbines

International Journal of Turbomachinery, Propulsion and Power
This paper presents an analysis of factors causing the change in the real gage factor of high-temperature strain gages installed with ceramic cements.
Oleksii Podobied, Ihor Vernyhora, Oleksii Kulikov   +2 more
doaj   +3 more sources

Development and analysis method of single element strain gage for stress intensity factor analysis in crack opening mode (Verification of analysis accuracy by simulated crack)

Nihon Kikai Gakkai ronbunshu, 2022
A dedicated strain gage has been developed to measure the stress intensity factor of cracks. Conventional strain gages dedicated to stress intensity factor analysis have been made by combining multiple elements into a single gage. Therefore, it took time
Shigeru KUROSAKI, Jyo SHIMURA, Syusaku YAMAJI, Mitsutaka KANEHIRA, Takeshi SHIMURA   +4 more
doaj   +1 more source

Out-of-plane bending stress intensity factor analysis of cracks in a strip using single-element strain gage

Nihon Kikai Gakkai ronbunshu, 2023
In recent years, the authors have developed a dedicated strain gage (hereafter referred to as a K-value gage) and an analysis method that can analyze the stress intensity factor of a crack with a single element.
Shigeru KUROSAKI, Jyo SHIMURA
doaj   +1 more source

Development and analysis method of single element strain gage for stress intensity factor analysis in crack opening mode (2nd report, development of grid angle 104° K value gage)

Nihon Kikai Gakkai ronbunshu, 2022
This paper shows the development and analysis method of a single element strain gage (K value gage) used to analyze the stress intensity factor of mode I (opening type) cracks. The K-value gage reported in the previous report collected the strain εθ with
Shigeru KUROSAKI, Jyo SHIMURA, Syuusaku YAMAJI, Mitsutaka KANEHIRA, Takeshi SHIMURA   +4 more
doaj   +1 more source

The opening mode stress intensity factor extraction method from mixed mode crack using single element strain gage.

Nihon Kikai Gakkai ronbunshu, 2022
Previously, the authors developed a strain gage (K-value gage) that can analyze the open mode stress intensity factor exclusively. This K-value gage was designed as a one-element strain gage with a gage width of 1 mm and a grid angle of 104° curvature ...
Shigeru KUROSAKI, Jyo SHIMURA, Syuusaku YAMAJI, Mitsutaka KANEHIRA, Takeshi SHIMURA   +4 more
doaj   +1 more source

Strain gage balance signal filtering with piecewise representations [PDF]

INCAS Bulletin, 2019
Strain gage balances provide the most important output of the supersonic wind tunnels. Typically, the time histories of the six forces/moments components must be filtered out, to provide useful results for performance assessment of the models.
Mihai Victor PRICOP, Sarif OMAR, Ionut BUNESCU, Alexandru Marius PANAIT   +3 more
doaj   +1 more source

Electromechanical properties of carbon-nanostructured elastomeric composites measured by digital image correlation

Composites Part C: Open Access, 2021
Tensile mechanical and piezoresistive properties of elastomeric (thermoplastic polyurethane) nanocomposites in film form, made of multiwall carbon nanotubes, multilayer graphene sheets and hybrid combinations of both are investigated using digital image ...
C. Pérez-Aranda, F. Avilés
doaj   +1 more source

Measuring Feed Force in Machining Using a Strain Gage

JEMMME (Journal of Energy, Mechanical, Material, and Manufacturing Engineering), 2021
Measuring the forces that work during machining has been being concerned by researchers for years. There are three main forces that work in turning: thrust force, axial force, and radial force.
Salman Al Farisi Siregar, Agus Triono, Mahros Darsin, Santoso Mulyadi   +3 more
doaj   +1 more source

Development of strain gages to analyze the stress intensity factor of a crack tip

Nihon Kikai Gakkai ronbunshu, 2015
There are currently one or two kinds of strain gages to measure the stress intensity factor. It might not be sometimes easy to analyze the stress intensity factor with those gages.
Shigeru KUROSAKI, Syusaku YAMAJI, Ryo KOBARI, Mitsutaka KANEHIRA, Takeshi SHIMURA, Jyo SHIMURA   +5 more
doaj   +1 more source