Results 131 to 140 of about 21,086 (292)

LTCC substrates for high performance strain gauges

, 2012
Recent advances in the development of high gauge factor thin-films for strain gauges prompt the research on advanced substrate materials. A glass ceramic composite has been developed in consideration of a high coefficient of thermal expansion and a low ...
Koppert, R., Rabe, Torsten, Bolte, J., Mieller, Björn, Gemeinert, Marion   +4 more
core  

Method for continuously measuring wheel/rail contact position using strain gauges

Nihon Kikai Gakkai ronbunshu
This paper describes a method for continuously measuring the contact position between the wheel and rail using strain gauges. The authors investigated the relationship between the bridge output sensitivity rate and the change in the placement of strain ...
Yoshinao NOGUCHI, Hiroyuki NISHIKORI
doaj   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Monitoring fracture healing with strain gauges: the effect on strain values of strain gauge location on the pin circumference

, 1995
In an attempt to establish some principles for the use of strain gauges in monitoring fracture healing, four strain gauges were fastened onto the most proximal pin of a Shearer external fixator applied to a hardwood fracture model.
O.O.A. Oni, C. Soutis, Oni, O. O A, Capper, M., M. Capper, Soutis, C.; id_orcid   +5 more
core   +1 more source

Dependance of Gauge Factor on Micro-Morphology of Sensitive Grids in Resistive Strain Gauges. [PDF]

Micromachines (Basel), 2022
Zhao Y, Wang Z, Tan S, Liu Y, Chen S, Li Y, Hao Q.   +6 more
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Smart Railway Traffic Monitoring Using Fiber Bragg Grating Strain Gauges. [PDF]

Sensors (Basel), 2022
Van Esbeen B, Finet C, Vandebrouck R, Kinet D, Boelen K, Guyot C, Kouroussis G, Caucheteur C.   +7 more
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Design and characterization of polymeric strain gauges for biomedical applications

, 2015
The market need for organic materials to be used in sensor design has increased with the growing interest in organic printed electronics. Therefore, it is important to find and investigate the piezoelectric and piezoresistive properties of organic ...
Almarghalani, Maan
core  

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source