Study of silicon strain gauges under electron irradiation [PDF]
Технологія та конструювання в електронній апаратурі, 2010 The characteristics of semiconductor strain gauges based on boron doped р-type silicon whiskers under high energy electron irradiation were studied. Strain gauges were irradiated at room temperature by electrons with energies 4,2–14 MeV and different ...
A. A. Druzhinin +5 more
doaj +2 more sources
Gauge Factor and Stretchability of Silicon-on-Polymer Strain Gauges
Sensors, 2013 Strain gauges are widely applied to measure mechanical deformation of structures and specimens. While metallic foil gauges usually have a gauge factor slightly over 2, single crystalline silicon demonstrates intrinsic gauge factors as high as 200 ...
Nanshu Lu, Shixuan Yang
doaj +2 more sources
Strain Gauges Based on CVD Graphene Layers and Exfoliated Graphene Nanoplatelets with Enhanced Reproducibility and Scalability for Large Quantities [PDF]
Sensors, 2017 The two-dimensional material graphene promises a broad variety of sensing activities. Based on its low weight and high versatility, the sensor density can significantly be increased on a structure, which can improve reliability and reduce fluctuation in ...
Volkan Yokaribas +5 more
doaj +2 more sources
ANALYSIS OF THE ACCURACY OF FIBRE-OPTIC STRAIN GAUGES [PDF]
Acta Polytechnica, 2013 In recent years, the field of structure monitoring has been making increasing use of systems based on fiber-optic technologies. Fiber-optic technology offers many advantages, including higher quality measurements, greater reliability, easier installation
Dita Jiroutová, Miroslav Vokáč
doaj +4 more sources
Low-temperature strain gauges based on silicon whiskers [PDF]
Tekhnologiya i Konstruirovanie v Elektronnoi Apparature, 2008 To create low-temperature strain gauges based on p-type silicon whiskers tensoresistive characteristics of these crystals in 4,2—300 K temperature range were studied.
Druzhinin A. A. +3 more
doaj +1 more source
Determining Magnitudes of Forces at Known Locations through a Strain Gauge Force Transducer
Sensors, 2023 A novel strain gauge force transducer was developed to minimize the number of strain gauges needed to determine the magnitudes of loads when the locations are known.
Edward Bednarz +4 more
doaj +1 more source
A time-strain monitoring system fabricated via offset lithographic printing [PDF]
, 2009 This paper reports progress in the development of strain sensors fabricated using the Conductive Lithographic Film (CLF) printing process. Strain sensitive structures printed via an unmodified offset lithographic printing press using a silver loaded ...
Hay, GI +5 more
core +4 more sources
Monitoring of the framings stress-strain with strain gauges [PDF]
E3S Web of Conferences, 2020 The article describes the research methods of the stress-strain of reinforced concrete framings (piles and pylons) using embedded strain gauges. The relations of load to indirect reactive characteristics displayed by the weighing device which were ...
Yurgaytis Alexey +3 more
doaj +1 more source
Use of Particle Image Velocimetry (PIV) technique to measure strains in geogrids [PDF]
E3S Web of Conferences, 2019 Geosynthetics are widely used in Geotechnical Engineering to reinforce soil/gravel in pavements, retaining wall backfills, and embankments. It is important to measure strains in geogrids in the determination of their strength parameters such as tensile ...
Gallage Chaminda, Jayalath Chamara
doaj +1 more source
Creep adjustment of strain gauges based on granular NiCr-carbon thin films [PDF]
Journal of Sensors and Sensor Systems, 2021 An important property of high-precision mechanical sensors such as force transducers or torque sensors is the so-called creep error. It is defined as the signal deviation over time at a constant load.
M. Mathis +5 more
doaj +1 more source