Results 91 to 100 of about 151,897 (279)
Possible correlation between work-hardening and fatigue-failure [PDF]
, 1969 Conceptual theory proposes that cyclic hardening due to non-uniform strain and stress amplitudes during testing, especially during the initial application of stress to a specimen, may correlate positively with the ultimate strength of the specimen under ...
Kettunen, P. O., Kocks, U. F.
core +1 more source
Applying an Ethical Lens to the Treatment of People With Multiple Sclerosis
Annals of Clinical and Translational Neurology, EarlyView.ABSTRACT The practice of neurology requires an understanding of clinical ethics for decision‐making. In multiple sclerosis (MS) care, there are a wide range of ethical considerations that may arise. These involve shared decision‐making around selection of a disease‐modifying therapy (DMT), risks and benefits of well‐studied medications in comparison to
Methma Udawatta, Farrah J. Mateen
wiley +1 more source
Effect of strain rate on bake hardening response of BH220 steel
EPJ Web of Conferences, 2015 This study aims at understanding the bake hardening ability of ultra low carbon BH220 steel at different strain rates. The as-received material has been pre-strained to four different levels and then deformed in tension under (a) as pre-strained state ...
Das Anindya +3 more
doaj +1 more source
Strain hardening of crystalline materials
ACI Avances en Ciencias e Ingenierías, 2010 To describe the work hardening process of crystalline materials in uniaxial deformation, a gradient-one-internal-variable model (GM1) constructed in the basis of the Kocks-Mecking model is proposed.
Edison A. Bonifaz
doaj +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Materials Research Letters, 2019 The temperature effect on the mechanical behavior of the HfNbTaTiZr high entropy alloy (HEA) was investigated at 77–673 K. The decrease of the yield strength with increasing the temperature was mechanistically analyzed by considering contributions from ...
S. Y. Chen +10 more
doaj +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy
Advanced Engineering Materials, EarlyView.An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley +1 more source
Advanced ScienceThe mechanical behavior and microstructural evolution of a BCC‐phase NbTaTiV refractory multi‐principal element alloy (RMPEA) is studied over a wide range of strain rates (10−3 to 103 s−1) and temperatures (room temperature to 850 °C).
Chanho Lee +18 more
doaj +1 more source