Results 211 to 220 of about 4,685,644 (340)
Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales
Advanced Engineering Materials, EarlyView.Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik +7 more
wiley +1 more source
A Lightweight Procedural Layer for Hybrid Experimental–Computational Workflows in Materials Science
Advanced Engineering Materials, EarlyView.We unveil a prototype hybrid‐workflow framework that fuses automatedcomputation with hands‐on experiments. Built atop pyiron, a lightweight, parameterized layer translates procedure descriptions into executable manual steps, syncing instrument settings, human interventions, and data capture in real‐time today.
Steffen Brinckmann +8 more
wiley +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
On strain localization under bending
The aim of the present contribution is to assess the localization properties of nonlocal damage models under bending. To permit a partially analytical treatment and to display the fundamental properties of various formulations, the idealized case of uniform bending is considered. This means that the beam has a constant cross section and is subjected to
Jirásek, Milan +1 more
openaire +1 more source
Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment
Advanced Engineering Materials, EarlyView.This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li +5 more
wiley +1 more source
On the prediction of ductile fracture by void coalescence and strain localization
, 2018 T. Luo, Xiaosheng Gao
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
The effect of water on strain localization in calcite fault gouge sheared at seismic slip rates
, 2017 M. Rempe +4 more
semanticscholar +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source