Results 151 to 160 of about 2,821,004 (350)

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Density, Microstructure, and Strain Rate-Dependent Behaviour of Polymeric Foams

, 2021
Kapil Bharadwaj Bhagavathula
openalex   +1 more source

High Strain Rate Response of Adhesively Bonded Fiber-Reinforced Composite Joints A Computational Study to Guide Experimental Design [PDF]

Adhesively bonded carbon fiber-reinforced epoxy composite laminates are widely used in aerospace applications. During a high energy impact event, these laminates are often subjected to high strain rate loading.
Justusson, Brian, Kidane, Addis, Pang, Jenna, Ravindran, Suraj, Sockalingam, Subramani, Sutton, Michael   +5 more
core   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

STRAIN-RATE EFFECTS [PDF]

, 1970
Klahn, Dale, Mukherjee, Amiya K., Dorn, John E.   +2 more
openaire   +4 more sources

610 Influence of strain rate and temperature on compression behavior of pure magnesium

, 2012
T. Terada, Hidetosi SOMEKAWA, Toshiji Mukai   +2 more
openalex   +1 more source

Laser Metal Deposited Ti4822 Hollow Pipe: Experimental and Computational Modelling Study

Advanced Engineering Materials, EarlyView.
Laser metal deposition (LMD) of a crack‐free built Ti4822 alloys is challenging. This article reports outstanding characteristics of a hollow pipe that is built with LMD technology when a predicted, nontransformation substrate temperature of 800 °C is used.
Sadiq A. Raji, Monnamme Tlotleng, Samuel Skhosane, Lehlogonolo R. Kanyane, Abimbola P. I. Popoola, Sisa L. Pityana   +5 more
wiley   +1 more source

3557 Strain Rate Dependency of Strength Properties of Lead-Free Solder

, 2006
Hiroyuki Takahashi, Minoru MUKAI, Takashi Kawakami   +2 more
openalex   +1 more source

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Closure to “Discussion of ‘An Experimental Study of Metal Extrusions at Various Strain Rates’” (1954, Trans. ASME, 76, p. 606) [PDF]

, 1954
J. Frisch, E. G. Thomsen
openalex   +1 more source