Results 221 to 230 of about 7,742,171 (287)

Analysing the High Strain Rate Behaviour of Cortical Bone with the Image-Based Inertial Impact (IBII) Test. [PDF]

J Dyn Behav Mater
Fletcher L, Pierron F.
europepmc   +1 more source

Design of a Multistable Finger Prosthesis with Programmable Metamaterials

Advanced Engineering Materials, EarlyView.
This research article shows the development of a multistable programmble metamaterial for the use as a finger prosthesis. The material was designed on different hierarchical levels where the influence of geometrical parameters and combination of mechanical elements was explored.
Franziska Wenz, Jannik Krohn, Alexander Leichner, Dilip Challisery, Heiko Andrae, Chris Eberl   +5 more
wiley   +1 more source

Dynamic Mechanical Properties and Damage Constitutive Model of Frozen-Thawed Basalt Fiber-Reinforced Concrete Under Wide Strain Rate Range. [PDF]

Materials (Basel)
Liang W, Wang S, Lv X, Li Y.
europepmc   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Effect of Geometrical Configuration and Strain Rate on Aluminum Alloy 5083 and S550 Steel Characterized by Digital Image Correlation. [PDF]

Sensors (Basel)
Chen C, Feng L.
europepmc   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Classification of impact damage patterns of cement cured soils in Pisha sandstone geopolymer based on critical strain rate. [PDF]

Sci Rep
Zhao X, Li X, Feng Z.
europepmc   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Strain-Rate-Dependent Tensile Behaviour and Viscoelastic Modelling of Kevlar^® 29 Plain-Woven Fabric for Ballistic Applications. [PDF]

Polymers (Basel)
Liu K, Feng Y, Kang B, Song J, Li Z, Wu Z, Zhang W.   +6 more
europepmc   +1 more source

A Novel Phenomenological Constitutive Model for Semi-Crystalline Polymers Across a Wide Strain-Rate Range. [PDF]

Polymers (Basel)
Zhang Y, Chi R, Wang S, Zhang X, Si J, Zhao Y, Cui G, Ma J.   +7 more
europepmc   +1 more source