Results 121 to 130 of about 382,947 (255)
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Review on Stress-Strain Rate Controllable Loading of Functionally Graded Materials
Gaoya wuli xuebaoGiven the dependence that key material dynamic properties in critical fields (e.g., national defense security and high-end manufacturing) have on stress-strain rate-controlled loading.
Chengcheng GUO +6 more
doaj +1 more source
Second Order Pyramidal Slip in Zinc [PDF]
, 1966 Measurements of strain, dislocation density, and dislocation velocity have been made in 99.999% Zn stressed in compression along the hexagonal axis, [0001]. Slip bands on the second order pyramid,〈1213〉{1212}, system were observed.
Adams, K. H. +3 more
core
Theory of metastability in simple metal nanowires
, 2005 Thermally induced conductance jumps of metal nanowires are modeled using stochastic Ginzburg-Landau field theories. Changes in radius are predicted to occur via the nucleation of surface kinks at the wire ends, consistent with recent electron microscopy ...
Bürki, J. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Effect of dynamic strain rate on micro-indentation properties of pure aluminum
EPJ Web of Conferences, 2015 Indentation is widely used to investigate the elastic and plastic properties of mechanical materials, which includes the strain rate sensitivity. The indentation exhibits an inhomogeneous strain distribution in contrast to compression and tensile tests ...
Yamada Hiroyuki +4 more
doaj +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Tensile creep-rate of pyrolytic carbon [PDF]
, 1970 Stress-change technique, combined with a graphical-interpolation analysis, yields data on the stress and temperature dependence of the creep rate over broad strain and stress or temperature ranges on as-deposited, substrate-nucleated, pyrolytic ...
Fischbach, D. B.
core +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source