Results 41 to 50 of about 15,204 (234)
Stepwise Transformation of Stress Induced Martensite in Ni-Ti Alloy [PDF]
ESOMAT 1989 - Ist European Symposium on Martensitic Transformations in Science and Technology, 1989 Superelasticity of N1T1 alloy is connected closely with stress induced phase transformation. Generally, stress-strain (6 2 ) curves are used to describe the mechanical behaviour. It is usefull to clearity the nature of the transformation at variant deformation stages corresponding to o-ecurve.
I. Jin, Y. Zhang
openaire +1 more source
A micromechanics inspired constitutive model for shape-memory alloys: the one-dimensional case [PDF]
, 2007 This paper presents a constitutive model for shape-memory alloys that builds on ideas generated from recent micromechanical studies of the underlying microstructure. The presentation here is in one dimension.
Bhattacharya, Kaushik, Sadjadpour, Amir
core +1 more source
Advanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Infrared imaging of TiNi shape memory alloy subjected to deformation at various temperatures
EPJ Web of Conferences, 2010 The infrared imaging of stress-induced martensitic transformation occurring in TiNi shape memory alloy subjected to deformation in various conditions has been presented.
Pieczyska E.A., Tobushi H.
doaj +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
The effect of thermomechanical treatment on the shape memory in heterophase Ni50,2Ti37,3Hf12,5 alloys [PDF]
, 2017 In this work the high-temperature shape memory effect was investigated in Ni50,2Ti37,3Hf12,5 alloys aged in austenite at 773 K 3h with/without an additional holding in the martensitic state under stress.
Суриков, Н. Ю. +1 more
core
Journal of Materials Research and TechnologyVaporization modeling of high-Mn steel during laser welding, along with the effects of Mn vaporization on the tensile properties at room and cryogenic temperatures, were investigated for various laser defocusing (LD) conditions. The LD10 exhibited a full
Myeonghwan Choi +3 more
doaj +1 more source
Karl Popper and the Mechanisms of Hydrogen Embrittlement
Advanced Engineering Materials, EarlyView.Representation of the beginning of loss of ductility rather than embrittlement. Small concentrations of hydrogen in a diffusible form within iron are well‐established to harm the mechanical integrity of steels. There are theories that attempt to explain the pernicious role of hydrogen.
H. K. D. H. Bhadeshia
wiley +1 more source
Materials Research, 2021 In this work, the residual stress study by XRD was carried out after martensitic transformation of a 304L steel subjected to plastic strain by rolling and tensile test, at room and cryogenic temperatures.
Juciane Maria Alves +2 more
doaj +1 more source
Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators
Advanced Engineering Materials, EarlyView.A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad +6 more
wiley +1 more source