Results 111 to 120 of about 1,201,583 (289)
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
Vestnik Samarskogo Gosudarstvennogo Tehničeskogo Universiteta. Seriâ: Fiziko-Matematičeskie Nauki, 2013 The problem of determining the stress-strain state of the thick-walled misaligned tube under internal pressure on steady-state creep is considered. The task linearization with the perturbation method is carried out.
Anna D Moskalik
doaj +1 more source
Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy
Advanced Engineering Materials, EarlyView.An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley +1 more source
STRESS AND STRAIN STATE OF REPAIRING SECTION OF PIPELINE
Известия высших учебных заведений и энергетических объединенний СНГ: Энергетика, 2015 Reliability of continuous operation of pipelines is an actual problem. For this reason should be developed an effective warning system of the main pipelines‘ failures and accidents not only in design and operation but also in selected repair.
V. V. Nikolaev
doaj
Novel direct method on the life prediction of component under high temperature-creep fatigue conditions [PDF]
, 2013 This paper presents a novel direct method, within the Linear Matching Method (LMM) framework, for the direct evaluation of steady state cyclic behaviour of structures subjected to high temperature – creep fatigue conditions.
Chen, Haofeng, Gorash, Yevgen
core
, 2010 Using coarse-grained molecular-dynamics simulations, a generic styrene-(block)-butadiene-(block)-styrene (SBS) triblock copolymer under lamellar conformation is used in order to investigate the mutual entanglement evolution when a structure of ...
Léonforte, F.
core +1 more source
Advanced Engineering Materials, EarlyView.Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
THE STRAIN- STRESS STATE OF STEEL REINFORCED CONCRETE BEAMS
Nauka ta progres transportu, 2010 The experimental investigations of steel-reinforced concrete beams composed of double-T No. 16 and the reinforced concrete slab of size 220×60×1200 mm were conducted.
A. V. Krukhmalov
doaj
Material Properties Measurements for Selected Materials [PDF]
Hugoniot equation of state measurements were made on Coconino sandstone, Vacaville basalt, Kaibab limestone, Mono Crater, pumice and Zelux (a polycarbonate resin) for pressures to 2 Mb. A single data point was obtained for fused quartz at 1.6 Mb.
Green, S. J. +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti +5 more
wiley +1 more source