Results 261 to 270 of about 286,581 (302)

Earthquake Stresses in Spherical Domes and in Cones

Journal of the Structural Division, 1956
Formulas for primary or membrane stresses in spherical domes and cones due to earthquake loading; earthquake forces are assumed to act in horizontal direction and in magnitude are equal to fraction of dead weight of structure itself; ordinary flexure formula may be used directly in determining meridional membrane stresses.
openaire   +1 more source

Prediction of stress–strain relation using cone indentation: effect of friction

International Journal for Numerical Methods in Engineering, 2004
AbstractAtkins and Tabor's approach (J. Mech. Phys. Solids 1965; 13: 149) for predicting uniaxial stress–strain relation of metals from cone indentation tests has been studied using numerical (finite element) simulation of cone indentation. Two indentation parameters, namely representative strain and constraint factor, which are central to the ...
DiCarlo, Anthony, Yang, Henry T. Y., Chandrasekar, Srinivasan   +2 more
openaire   +1 more source

Vaginal cones in stress incontinence treatment.

Nursing times, 2008
Jeanette Haslam explains the theory that underpins the use of vaginal cones in stress urinary incontinence and how this translates into practice.
openaire   +1 more source

Pelvic floor exercises versus vaginal weight cones in genuine stress incontinence

European Journal of Obstetrics & Gynecology and Reproductive Biology, 1998
To compare pelvic floor exercises and vaginal weight cones in the treatment of genuine stress incontinence.Randomised controlled trial.Sixty ambulatory and fit white women (mean age 56 years) with urinary stress incontinence, treated by a single physiotherapist as outpatients during twelve weeks.
H, Cammu, M, Van Nylen
openaire   +2 more sources

Recovery of Stresses in a Beam from those in a Cone

Journal of Elasticity, 1998
The authors study the stressed state of the interior of a truncated wedge (two-dimensional case) or of the interior of a truncated cone (three-dimensional case). To emphasize the correctness of these results, a comparison is made with results given by the Saint-Venant's theory when passing to the limit, obtaining thus a rectangle or a cylinder of the ...
Knops, R. J., Villaggio, P.
openaire   +2 more sources

Clinical Value of Vaginal Cones for the Management of Female Stress Incontinence

The Journal of Urology, 1997
In women with mild stress incontinence (mean urine loss of 3.7 g/h), pelvic floor training using vaginal cones resulted in a subjective success rate of 70% (19/27), that is complete cure or reduction by >50% of the original severity. However, in women with severe stress incontinence (mean urine loss of 20.7 g/h) cone therapy was successful in only 14% (
K, Kato, A, Kondo
openaire   +2 more sources

Axisymmetric Problem of Stressed State for a Twice Truncated Cone

Journal of Mathematical Sciences, 2014
We consider an axisymmetric mixed problem of stressed state for a twice-truncated cone with regard for its own weight and the conditions of smooth contact imposed on its conical surface. The application of a new integral transformation with respect to the meridian angle directly to the Lame equations reduces the problem in the space oftransforms to a ...
N. D. Vaisfel’d, G. Ya. Popov, A. V. Reut   +2 more
openaire   +1 more source

Motion and stability of cones in a yield stress fluid

AIChE Journal, 2014
This experimental study focuses on the creeping flow of a shear thinning yield stress fluid around conical obstacles. The flow has been analyzed in steady state and with adherence conditions. Firstly, the influences of the cone apex angle and of the Oldroyd number, that is the ratio between plastic and viscous effects, on the drag coefficient have been
Ahonguio, Fiacre, Jossic, Laurent, Magnin, Albert   +2 more
openaire   +2 more sources

Stress-Corrosion Cracking of a Pandia Digester Inlet Cone

2019
Abstract The Pandia digester is a long cylindrical vessel which uses alkaline sulfite liquor to cook sawdust for pulping. The inlet cone was fabricated from AISI 304L stainless steel with E308 welds. Typical liquor concentration was approximately 80% NaOH, 20% Na2SO3 with chloride concentrations at 2 grams per liter.
openaire   +1 more source

Eddies inside a liquid cone stressed by interfacial electrical shear

Colloids and Surfaces, 1992
Abstract The velocity profile inside the liquid cone at the base of an electrically driven jet is examined by inserting tracer particles into the liquid. Observations of these particles at high magnification demonstrated the presence of an axisymmetric circulation inside the cone due to interfacial electrical shear stresses.
openaire   +1 more source