Results 101 to 110 of about 2,785 (231)

Strut and tie modeling for RC short beams with corroded stirrups

Latin American Journal of Solids and Structures
Corrosion of steel reinforcement is one of the major problems that shorten the service life of reinforced concrete (RC) structures. Steel stirrups, due to their location as an outer reinforcement, are more susceptible to corrosion problems and damage ...
Ahmed K. El-Sayed
doaj   +1 more source

Analysis and design of disturbed regions with strut-tie models

, 1992
An interactive computer graphics program implementing the Strut-Tie model approach for analysis and design of reinforced and prestressed concrete members is presented. The program consists of three parts.
Alshegeir, Abdulsallam A
core  

An Innovative Test Method for Tensile Strength of Concrete by Applying the Strut-and-Tie Methodology. [PDF]

Materials (Basel), 2020
Liao WC, Chen PS, Hung CW, Wagh SK.
europepmc   +1 more source

Model Strut and Tie dengan Software BESO2D pada Balok dengan a/d = 3,70 [PDF]

Balok beton bertulang merupakan komponen struktur utama yang berperan dalam meneruskan beban dari pelat lantai ke kolom dan selanjutnya ke fondasi. Kemampuan balok dalam menahan beban ditentukan oleh tulangan lentur yang berfungsi untuk menahan momen ...
Delenty, Natasya
core  

Shear Strength Prediction of RC Beam-column Sandwich Interior Joints Based on Simplified Softened Strut-and-Tie

, 2017
Introduction: The sandwich joints casted core area with weaker strength concrete of beam, has more advantages than the traditional joints casted core area with higher strength concrete of column, such as the simple ...
Yue Qi, Ruiyun Zhang, Weiming Yan, Shicai Chen, Liqun Hou   +4 more
core   +1 more source

Strut-and-Tie Models of Masonry Shear Walls

, 2018
This paper contains theoretical fundamentals of strut and tie models, used in unreinforced horizontal shear walls. Depending on support conditions and wall loading, we can distinguish models with discrete bars when point load is applied to the wall (type I model) or with continuous bars (type II model) when load is uniformly distributed at the wall ...
openaire   +2 more sources

7th International Conference on Civil and Structural Engineering: Optimization and Control in Civil and Structural Engineering

, 1999
The strut-and-tie modeling is a simple, unified, rational and safe approach for the design of structural concrete members. Conventional methods are not efficient in finding optimal strut-and-tie models in concrete members with complex geometry and ...
Steven, G. P., Liang, Q. Q., Xie, Y. M.
core  

Strut Method for the Analysis of Confined Masonry Structure with Opening

Electronic Journal of Structural Engineering
Confined masonry construction (CM) is an efficient earthquake-resistant structural system that consist of masonry walls as the main structure and RC tie column and beam as confining elements.
Ida Ayu Made Budiwati, Made Sukrawa, Ida Bagus Prastha Bhisama   +2 more
doaj  

Effect of loading type in concrete deep beam with strut reinforcement

Open Engineering
This study examined eight specimens of two groups of deep beam (DB) with the same dimensions and reinforcement quantity, where the first group had four specimens tested under two-point loads and the second group had four specimens tested under one-point ...
Kadhim Hussein Kamal, Abdullah Mazin Diwan   +1 more
doaj   +1 more source

Analysis of shear resisting actions by means of optimization of strut and tie models taking into account crack patterns

, 2018
The shear resisting actions in reinforced concrete elements without transverse reinforcement is analyzed by means of optimized strut-and-tie models with concrete ties. Biaxial failure criteria are used for uncracked and cracked regions.
Marí Bernat, Antonio Ricardo, Cladera Bohigas, Antoni, Antoni Cladera, Jesús Miguel Bairán, Antonio Marí, Bairán García, Jesús Miguel   +5 more
core   +1 more source