Results 111 to 120 of about 2,785 (231)

ISEC 4: Innovations in Structural Engineering and Construction [PDF]

, 2008
This paper presents the performance-based optimization of strut-and-tie models in reinforced concrete deep beams. The performance-based optimization (PBO) technique combines performance-based design concepts with modern topology optimization technologies
Ng, A. W. M., Liang, Q. Q.
core  

Modified Softened Strut and Tie Model for Concrete Deep Beams

Journal of Engineering and Sustainable Development, 2012
A modified softened strut-and-tie model (MSST) for determining the shear strength of reinforced concrete deep beams is proposed in this paper. It is a simplified analytical model and several improvements have been made.
Mohammed M. Rasheed
doaj  

Strut-and-Tie Method for GFRP-RC Deep Members

International Journal of Concrete Structures and Materials
The current code provisions in ACI 440.11 are based on the flexural theory that applies to slender members and may not represent the actual structural behavior when the shear span-to-reinforcement depth ratio is less than 2.5 (i.e., deep members).
Zahid Hussain, Antonio Nanni
doaj   +1 more source

Basics of Strut-And-Tie model designing [PDF]

, 2014
V projektni nalogi so predstavljene osnove dimenzioniranja z uporabo modela razpor in vezi. Napetostno polje v konstrukcijskih elementih je osnova za izbiro modela razpor in vezi, zato je prikazan izračun napetostnega polja in potek trajektorij glavnih ...
Ledinek, Matic
core  

Blocos de concreto armado sobre seis estacas: simulação numérica e dimensionamento pelo método de bielas e tirantes

Revista IBRACON de Estruturas e Materiais
Este artigo analisa o comportamento estrutural de blocos de concreto armado sobre seis estacas dispostas em arranjo retangular. Considerou-se a deformabilidade do solo de apoio das estacas, diferentes resistências para o concreto e pilares com seções ...
D. S. Oliveira, R. Barros, J. S. Giongo
doaj   +1 more source

Direct Strut-and-Tie Model for Ultimate Shear Strength of Reinforced Concrete Structural Walls

, 2011
A direct strut-and-tie model to calculate the ultimate shear strength of structural walls based on an interactive mechanical model (C.Y.Tang et al.) is presented. Two common failure modes, namely, diagonal splitting and concrete crushing, are examined in
Masanobu Sakashita, Yi Lin Sun, Ji Yang Wang   +2 more
core   +1 more source

Perancangan Pile Cap Menggunakan Metode Strut and Tie Model

The design of the pile cap structure generally involves a conventional method that assumes that all areas are linear. The reality distribution strain in cross-section structure pile cap experiences non-linear strain.
Wijaya, Annisa, Sukarman
core   +1 more source

EXPERIMENTAL VERIFICATION OF STRUT AND TIE METHOD FOR REINFORCED CONCRETE DEEP BEAMS UNDER VARIOUS TYPES OF LOADINGS

Journal of Engineering and Sustainable Development, 2017
Strut-and-tie method (STM) is a very useful tool to design irregular concrete members. This work presents the results of the experimental tests conducted on three self-compacting reinforced concrete deep beams that had a constant cross-section of 150 mm×
Khattab Saleem Abdul-Razzaq, Sarah Farhan Jebur   +1 more
doaj  

Analysis and design of a reinforced concrete wall with openings using strut-and-tie models

, 2018
U radu je prikazan proračun armiranobetonskog zida s nesimetrično razmaknutim otvorima po visini primjenom štapnih modela. Rad se sastoji od dva dijela.
Drakulović, Boris
core  

Model Strut and Tie dengan Software BESO2D pada Balok dengan Bentang Geser 500 mm [PDF]

Balok beton bertulang merupakan salah satu elemen struktur utama yang berfungsi menyalurkan beban dari pelat lantai menuju kolom dan fondasi. Kapasitas balok dalam menahan beban dipengaruhi oleh kombinasi kerja antara tulangan lentur dalam menahan momen ...
Zahiroh, Aliyyah Putri
core