Results 101 to 110 of about 16,885 (229)
, 2011 Cílem této bakalářské práce je analýza současných konceptů podvozků závodních okruhových aut. V první části práce je zpracován historický vývoj, charakteristika kol a pneumatik s reprezentací dobře známých produktů.
Macháček, Tomáš
core
Experimental Verification of Strut and Tie Model Design Method [PDF]
ACI Structural Journal, 2007 Although strut-and-tie models (STM) appear to provide safe, lower-bound designs for irregular concrete members, there have not been many experimental validations of them. This paper presents the result from two series of testing of STM specimens. In the first series, 6 specimens having different reinforcing designs but the same overall geometry and ...
openaire +1 more source
The Baltic Journal of Road and Bridge Engineering, 2018 The primary aim of this article is to present design approaches for calculating the additional strengthening of masonry arches with the use of the Strut-and-Tie model and applicable standards and their comparison to the experiments.
Martin Zlámal, Petr Štěpánek
doaj +1 more source
Studi Parametrik Pertemuan Balok Kolom Interior Pada Portal Beton Bertulang Menggunakan Metode Strut and Tie [PDF]
, 2016 Untuk mendesain D-region diperlukan analisa yang lebih mendalam dengan berdasar pada bentuk trajektori tegangan elemen yang ditinjau. Tujuan dari penelitian ini adalah untuk mengetahui bentuk trajektori tegangan, jumlah tulangan serta konfigurasi ...
Hunggurami, E. (Elia) +2 more
core +1 more source
Utilizing the Strut-and-Tie Model for the Design and Analysis of Deep Beams
Modelling in Civil Environmental EngineeringReinforced concrete deep beams, distinguished by a low shear span-to-depth ratio, exhibit complex, nonlinear strain distributions that render conventional beam theory inadequate.
Platon Mihai
doaj +1 more source
Pengaruh Panjang Penyaluran Terhadap Kuat Cabut Tulangan Baja [PDF]
, 2010 Salah satu persyaratan dalam perancangan beton bertulang yang harus diperhatikan adalah panjangpenyaluran tulangan. Panjang penyaluran adalah panjang penambatan yang diperlukan untukmengembangkan tegangan luluh pada tulangan yang merupakan fungsi dari ...
Ginting, A. (Arusmalem) +1 more
core
Strut-and-Tie Models of Masonry Shear Walls
, 2018 This paper contains theoretical fundamentals of strut and tie models, used in unreinforced horizontal shear walls. Depending on support conditions and wall loading, we can distinguish models with discrete bars when point load is applied to the wall (type I model) or with continuous bars (type II model) when load is uniformly distributed at the wall ...
openaire +2 more sources
Development of strut and tie models for simply supported deep beams using topology optimization [PDF]
Songklanakarin Journal of Science and Technology (SJST), 2008 Generally, structural members can be broadly divided into two regions, namely B, or Bernoulli regions, where the strain distributions are linear and D, or Disturbed regions, where the strain distributions are nonlinear While well defined theories are ...
Praveen Nagarajan, T.M. Madhavan Pillai
doaj
Validation of a simplified model for the design of masonry infilled frames [PDF]
, 2006 The design of masonry infills is an issue that has attracted the attention of several researchers in the past, both from the experimental and analytical points of view.
Alvarenga, Rita de Cássia S. S. +2 more
core
Strut Method for the Analysis of Confined Masonry Structure with Opening
Electronic Journal of Structural EngineeringConfined masonry construction (CM) is an efficient earthquake-resistant structural system that consist of masonry walls as the main structure and RC tie column and beam as confining elements.
Ida Ayu Made Budiwati +2 more
doaj