Results 91 to 100 of about 1,140 (131)

Development of Strut-and-Tie Models in Deep Beams with Web Openings

, 2007
The strut-and-tie models of a total of fourteen (14) concrete deep beams with varying size and location of web openings are developed herein using a topology optimisation approach. By systematically eliminating inefficient materials from an over-designed
Guan, Hong, Doh, Jeung-Hwan
core   +1 more source

Analysis and design of a reinforced concrete wall with openings using strut-and-tie models

, 2018
U radu je prikazan proračun armiranobetonskog zida s nesimetrično razmaknutim otvorima po visini primjenom štapnih modela. Rad se sastoji od dva dijela.
Drakulović, Boris
core  

Application of micro truss and strut and tie model for analysis and design of reinforced concrete structural elements [PDF]

Songklanakarin Journal of Science and Technology (SJST), 2010
Generally structural members can be broadly divided into two regions, namely B or Bernoulli regions where the strain distributions are linear, and D or disturbed regions where the strain distributions are nonlinear.
Praveen Nagarajan, U.B. Jayadeep, T.M.Madhavan Pillai   +2 more
doaj  

Experimental verification of continuous deep beams with openings designed using strut-and-tie modelling

, 2009
This study investigates the applicability and reliability of the strut-and-tie modelling that is recommended by the ACI 318 Building Code (2002) for designing continuous deep beams with openings.
Li, Bing., Wu, T., T. Wu, B. Li
core   +1 more source

Behavior predictions of deep beams with short straight bar anchorages using strut-and-tie models and nonlinear analysis

Revista IBRACON de Estruturas e Materiais
This paper investigates the laboratory test results of 12 deep beams available in the literature, where the longitudinal reinforcement was anchored into the support using short straight bar anchorages.
R. A. SOUZA, S. BREÑA
doaj   +1 more source

Shear Strength Prediction of RC Beam-column Sandwich Interior Joints Based on Simplified Softened Strut-and-Tie

, 2017
Introduction: The sandwich joints casted core area with weaker strength concrete of beam, has more advantages than the traditional joints casted core area with higher strength concrete of column, such as the simple ...
Yue Qi, Ruiyun Zhang, Weiming Yan, Shicai Chen, Liqun Hou   +4 more
core   +1 more source

Ristikkomenetelmä (Strut-and-tie modeling) [PDF]

, 2014
Tämän opinnäytetyön toimeksianto saatiin Wise Group Finland Oy:ltä. Opinnäytetyössä perehdyttiin ristikkomenetelmään ja sen soveltamiseen rakennesuunnittelussa talonrakennuskohteissa.
Koskimies, Joonas
core  

Strut-and-tie modeling of two-dimensional reinforced concrete structural elements

, 2005
This thesis focused on the applicability of truss models and the strut-and-tie method to the analysis and design of reinforced concrete beams and structural walls with opening that had complicated internal stress flow and to develop a design procedure ...
Zhao, Yiwen
core   +1 more source

Design of non-flexural components using strut and tie models

, 2003
In this paper, the design of non-flexural components using strut and tie models (STM) is presented. The proposed design procedure of STM is compliant with the British Standards.
Su, RKL, Chandler, AM, Wong, PCW
core  

An Indeterminate Strut-Tie Model and Load Distribution Ratio for RC Deep Beams- (II) Validity Evaluation

, 2011
In this study, the ultimate strength of 234 simply supported reinforced concrete deep beams tested to shear failure was evaluated by the ACI 318M-08's strut-tie model approach implemented with the indeterminate strut-tie model and load distribution ...
Young-Mook Yun, Byung-Hun Kim
core   +1 more source