Results 101 to 110 of about 1,298 (216)

Strut-and-Tie Models of Masonry Shear Walls

, 2018
This paper contains theoretical fundamentals of strut and tie models, used in unreinforced horizontal shear walls. Depending on support conditions and wall loading, we can distinguish models with discrete bars when point load is applied to the wall (type I model) or with continuous bars (type II model) when load is uniformly distributed at the wall ...
openaire   +2 more sources

Analysis and design of a reinforced concrete wall with openings using strut-and-tie models

, 2018
U radu je prikazan proračun armiranobetonskog zida s nesimetrično razmaknutim otvorima po visini primjenom štapnih modela. Rad se sastoji od dva dijela.
Drakulović, Boris
core   +2 more sources

The influence of connecting pile cap-column in the mechanisms of break in the two pile caps

Revista IBRACON de Estruturas e Materiais
The paper analyzes the two pile caps with partially embedded socket and subject a center load. Three models were experimentally tested, varying the type of conformation of the column and walls of the socket, with a smooth, the other rough, and a ...
A. C. MESQUITA, A. S. ROCHA, R. G. DELALIBERA, W. A. DA SILVA   +3 more
doaj   +1 more source

Computer Automated Performance-based Optimization of Strut-and-tie Models in Reinforced Concrete Corbels

, 2008
This paper presents computer automated performance-based optimization of strut-and-tie models in reinforced concrete corbels. The automated performance-based optimization (PBO) technique is used to develop optimal strut-and-tie models for the design ...
Fragomeni, Sam, Liang, Qing
core  

Strut and tie model for concrete beams

, 2009
The strut-and-tie model was developed in 1899 and was first used in the calculations of the concrete members experiencing both shear and torsion. As the strut-and-tie model design became more frequently used, the strut-and-tie model was further applied ...
Chen, Limin.
core  

Variation analysis effects of square and rectangular columns section with different longitudinal reinforcement rates in the main reinforcement two pile caps analysis

Revista IBRACON de Estruturas e Materiais
The transition between the columns of building and foundation had been used the pile-cap structural elements. The most appropriate method for the pile caps design is the Strut and Tie model.
F. S. MUNHOZ, J.S. GIONGO
doaj   +1 more source

Reliability analysis in strut and tie models

, 2013
Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - CAPESThis work explores the use of reliability techniques for selecting strut and tie models and explores the use of topology optimization techniques to generate these models automatically ...
Santos, Victor Mark Pontes dos
core  

Development and design of strut-and-tie models in reinforced concrete deep beams

, 2009
This paper presents a performance-based optimization method for developing strut-and-tie models in reinforced concrete deep beams. Guidelines derived from optimized results obtained from recent research for developing strut-and-tie models in reinforced ...
Fragomeni, Sam, Liang, Qing
core  

Analysis of Shear Model for Steel-Fiber-Reinforced High-Strength Concrete Corbels with Welded-Anchorage Longitudinal Reinforcement. [PDF]

Materials (Basel), 2023
Li SS, Peng D, Wang H, Zhang FJ, Li HM, Xie YJ, Chen AJ, Xie W.   +7 more
europepmc   +1 more source

Experimental Study of Shear Performance of High-Strength Concrete Deep Beams with Longitudinal Reinforcement with Anchor Plate. [PDF]

Materials (Basel), 2023
Li SS, Jin TC, Zheng LA, Zhang GY, Li HM, Chen AJ, Xie W.   +6 more
europepmc   +1 more source