Results 131 to 140 of about 6,144,940 (303)
A Study on College Students’ Life Satisfaction
Lavai - International Journal of EducationThis study was based on the " Satisfaction with Life Scale " written by Diner in 1985 and included college students (n=300) from NUM, MNUE, MULS in order to analyze the psychometric indicators of the scale. The reliability of the scale was 0.86 and the test-retest coefficients was 0.67 in a follow-up study three months later (n=77).
Aruna +2 more
openaire +2 more sources
Soft Mechanical‐Electrical Logic Using Liquid Metal‐Filled 3D‐Printed Architectures
Advanced Engineering Materials, EarlyView.We present 3D‐printed soft mechanical–electrical logic elements that use liquid metal–filled silicone tubes actuated by thermoplastic polyurethane/polylactic acid (TPU/PLA) architectures to produce Boolean operations. Complementary normally open and normally closed unit cells perform repeatable binary transitions and can be combined into more complex ...
Christoph Lehmann +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley +1 more source
Factors of Student Satisfaction by Students’ Postures
The Proceedings of the Annual Convention of the Japanese Psychological Association, 2023 Atsuhiko Uchida, Akira Harada
openaire +1 more source
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
RESEARCH ON STUDENTS’ SATISFACTION WITH BANKING SERVICES
International journal of multidisciplinarity in business and science, 2017 The aim of the research was to investigate which banking services students’ use, which banks they prefer, to define which dimensions or elements of banking services are important for them, and to determine the level of students’ satisfaction with each dimension of the mentioned services.
Mandić, Miroslav, Rešetar, Mateja
openaire +3 more sources