Magnetizing Characteristics of Bridge Type Superconducting Fault Current Limiter (SFCL) with Simultaneous Quench Using Flux-Coupling [PDF]
Energies, 2020 A bridge type superconducting fault current limiter (SFCL) with simultaneous quench using two high-temperature superconducting (HTSC) elements and two coils was fabricated to analyze the fault current limiting characteristics.
Seok-Cheol Ko, Tae-Hee Han, Sung-Hun Lim
doaj +5 more sources
Analisa Penggunaan Superconducting Fault Current Limiter (SFCL) Untuk Melindungi Peralatan di PT Pindo Deli [PDF]
Jurnal Teknik ITS, 2015 Increas demand load and power capacity requirement at PT Pindo Deli then the short circuit current that occur will be greater. this can cause damage to electrical equipment located around the point of interrupting and resulting failure of the electrical ...
Yohanes Sabriant Widyo Utomo +1 more
doaj +7 more sources
Combining finite element and reinforcement learning methods to design superconducting coils of saturated iron-core superconducting fault current limiter in the DC power system. [PDF]
PLoS One, 2023 A saturated iron-core type superconducting fault current limiter (SI-SFCL) can effectively restrict the magnitude of the fault current and alleviate the strain on circuit breakers in DC power systems.
Kim CS +5 more
europepmc +2 more sources
Superconducting Surge Current Limiter
Energies, 2021 A superconducting fault current limiter (SFCL) for medium voltage networks cooled by a cryocooler was designed, built and tested by the current author. For the construction of this limiter, a high-temperature second generation superconducting tape (HTS ...
Sławomir Kozak
doaj +2 more sources
Application Simulation of a Resistive Type Superconducting Fault Current Limiter (SFCL) in a Transmission and Wind Power System [PDF]
Energy Procedia, 2015 Due to the increased fault-level currents, superconducting fault current limiter (SFCL) is more likely to penetrate into a low voltage and medium voltage transmission network to improve their stability and lower the electric devices capacity.
Jiahui Zhu, Jianwei Li, Weijia Yuan
exaly +4 more sources
Modeling of RC-IGCT-based superconducting hybrid DC circuit breaker with TP KEMA arc model and hybrid SFCL. [PDF]
Sci RepAchieving rapid fault clearance in medium-voltage direct current (MVDC) grids requires DC circuit breakers (DCCBs) with high current-interrupting capability and low cost. Our team previously proposed a hybrid DC circuit breaker combining Asymmetric IGCT (
Junaid M, Wang X, Yu D, Peng Y.
europepmc +2 more sources
First Russian 220 kV Superconducting Fault Current Limiter (SFCL) For Application in City Grid
IEEE Transactions on Applied Superconductivity, 2021 The superconducting fault current limiter (SFCL) for a nominal voltage of 220 kV and a rated current of 1200 A was developed by SuperOx company to be applied in high voltage substation in Moscow, Russia. The device is a three-phase dead-tank apparatus and is equipped with a closed-cycle cryocooling system.
Daria Gorbunova, Mikhail Moyzykh
exaly +2 more sources
Optimal application research of superconducting fault current limiters on medium voltage direct current shipboard power system. [PDF]
Sci RepMedium voltage direct current shipboard power system (MVDC SPS) is the development trend of navy in the future. At present, one of the bottlenecks restricting the development of MVDC SPS is that the short fault. This paper presents a method of applying a
Zhou Y, Ren L, Xu Y, Shi J.
europepmc +2 more sources
A novel controllable capacitor commutation based superconducting hybrid direct current breaker. [PDF]
Sci RepFeaturing low power loss and high reliability, voltage source converter medium voltage direct current (VSC-MVDC) systems have been widely employed for grid-tied renewable energy applications.
Xu Y +5 more
europepmc +2 more sources
Forces and Stresses in the Windings of a Superconducting Fault Current Limiter
Energies, 2022 This paper presents the design of a Superconducting Fault Current Limiter (SFCL) and calculation results of forces and stresses in the windings of a resistive fault current limiter.
Janusz Kozak
doaj +1 more source