Results 241 to 250 of about 228,648 (305)

Ultrasonic Vibration-Assisted Micro-Electrical Discharge Machining Characteristics and Parameter Optimization of C/SiC Composites. [PDF]

Micromachines (Basel)
Yu P, Wang L, Gao Y, Li Q, Li Y.
europepmc   +1 more source

Enhanced production of active species and NH₃ using non-equilibrium ferroelectric barrier discharge. [PDF]

Nat Commun
Xu Y, Chang Z, Shi Z, Sun Z, Burda H, Wang W, Liu N, Ju Y.   +7 more
europepmc   +1 more source

Elevated Release of Presynaptic Glutamate: The Potential Pathogenesis of Anti-NMDAR Encephalitis-Associated Seizures. [PDF]

CNS Neurosci Ther
Huang H, Huang Y, Li S, Wu Y, Yang S, Wu Y.   +5 more
europepmc   +1 more source

Current trends in radiocarbon in Skagerrak and Kattegat assessed by brown algae from Swedish coastal waters. [PDF]

Radiat Prot Dosimetry
Eriksson Stenström K, Mattsson S.
europepmc   +1 more source

Sliding Surface Discharge on a Conducting Surface

, 1994
Mitko, Sergey V., Paramonov, A.V., van Goor, Frederik Albert, Ochkin, V.N., Witteman, Wilhelmus Jacobus   +4 more
openaire   +1 more source

Development of a Robust Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) Cell for Elucidating Reaction Mechanisms in Nonthermal Plasma Catalysis. [PDF]

Small Methods
Niu J, Chen S, Chen Y, Zhang J, Zhou G, Yu H, Lin Q, Liu T, Xu S, Li Z, Huang J, Chen H, Fan X.   +12 more
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Electrical discharge surface alloying

Journal of Materials Processing Technology, 2004
Abstract This paper details the electrical discharge surface alloying/modification of γ-TiAl (Ti–46.5Al–4(Cr, Nb, Ta, B)) and α/β Ti alloy (Ti–6Al–4V) sheet (1 mm thick) during wire cutting using deionised water dielectric with nickel and copper wires.
H.G Lee, J Simao, D.K Aspinwall, R.C Dewes, W Voice   +4 more
openaire   +2 more sources

Surface streamer microwave discharge

Technical Physics, 2002
An atmospheric-pressure pulsed microwave discharge on the surface of an insulating plate and between two insulating fllms is considered. The discharge is initiated in a quasi-optical microwave beam away from the beam-forming elements. The TEM field of the beam is less than the critical breakdown value.
K. V. Aleksandrov, L. P. Grachev, I. I. Esakov, K. V. Khodataev   +3 more
openaire   +1 more source

Pulse-periodic surface discharge

Soviet Journal of Quantum Electronics, 1983
An investigation was made of a pulse-periodic surface (gliding) discharge of the kind used in electric-discharge excimer lasers. In contrast to a bulk discharge, the surface discharge remained homogeneous at high pulse repetition frequencies without the need to replace the gas in the discharge zone.
V M Borisov, F I Vysikaĭlo, Yu B Kiryukhin, O B Khristoforov   +3 more
openaire   +1 more source

Surface discharges on polymeric insulator shed surfaces

IEEE Transactions on Dielectrics and Electrical Insulation, 1997
This paper describes results of an experimental investigation into surface discharges occurring on the surface of polymeric insulators. Discharges on partially hydrophobic surfaces were found to occur across well defined dry bands, while discharges on hydrophobic surfaces appeared as small points of light occurring between discrete water drops.
P. Blackmore, D. Birtwhistle
openaire   +1 more source